www.dbtechnologies.com
OPERA UNICA 12
cod. 420120269Q REV.1.0
Technical Data
Speaker Type
:
2-way active speaker
Usable Bandwidth [-10 dB]
:
67 – 20000 Hz
Frequency Response [-6 dB]
:
73 – 20000 Hz
Max SPL (1 m)
:
132 dB
HF compression driver
:
1 " Exit
HF voice coil
:
1.75”
LF
:
12” (Neodymium)
LF Voice Coil
:
3”
Crossover frequency:
1600 Hz
FIR filters:
yes
Horizontal dispersion
:
110° (85° up / 120° down)
Vertical dispersion
:
85° (+25°/ -60°)
Amplifier
Amp Technology
:
Digipro® G3
Auto-range
Amp Class
:
Class-D
RMS Power
:
900 W
Peak Power:
1800 W
Operating voltage:
220-240V~ (50-60 Hz) or 100-120V~ (50-60 Hz)
Processor
Controller
: 56 bit
DSP, 24 bit/48 kHz AD/DA converter
Limiter
:
Peak, RMS, Thermal
Controls
:
DSP rotary control (8 presets), Input
sensitivity switch, input sensitivity level
Input/Output
Mains/link connections
:
powerCON® type
Signal Input/Link
:
Balanced XLR type
RDNet connections:
Data in, Data out
Daisy chain power connection (max number of OPERA
UNICA 12):
6 (1+5) (220-240V~) / 3 (1+2) (100-120V~)
Mechanics
Housing:
Polypropylene
Grille
:
Full grille
Rigging points
: (
2x) M10 on top + (1x) M10 on the rear
Pole Mount
:
yes, 36 mm diameter
Width
:
350 mm (13.78 in)
Height
:
642 mm (25.28 in)
Depth
:
349 mm (13.74 in)
Weight
:
15 kg (33.07 lbs.)
Download the complete user manual on:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
WARNING:
Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
Scan with your QR Reader
App to download the
complete User Manual
