background image

5M78 

AC Strain Gage Conditioner Module

Product Warranty and Repair

Daytronic Corporation warrants its products to be free from defects in material and
workmanship, under normal and proper use in accordance with our instructions,
for the period of time specified below.  Our liability under such warranty or in 
connection with any other claim relating to the products shall be limited to, at our
option, the repair or replacement of any products or parts or components thereof
which are returned to us freight prepaid and which are defective in material or 
workmanship or the refund of the purchase price to the Buyer.

Before returning a product or products for any reason, the

customer must call 

Daytronic Customer Support Services

 at 

ALL EQUIPMENT TO BE REPAIRED OR REPLACED UNDER WARRANTY MUST BE
RETURNED TO THE FACTORY.  

.  Once the customer has provided the

necessary information and has been assigned a specific RMA, the product(s) in question
may be returned to Daytronic by shipping it 

Daytronic Corp. , 1000 New Durham Road, Edison, New Jersey 08818

ANY PRODUCT FOUND TO BE DAMAGED THROUGH CUSTOMER NEGLIGENCE OR MIS-

USE MAY BE EXCLUDED FROM ANY AND ALL POLICIES CONTAINED IN THIS DOCUMENT.

(937) 866-3300 

to request a

RETURN MATERIAL AUTHORIZATION (RMA)

Daytronic Customer Service: 1-800-668-4745      [email protected]

Содержание 5M78

















Отзывы: