Dawlance DDW 1480 I INV, Руководство пользователя

Страница: 6 / 23

Installation
Permitted water temperature: up
to 25°C
The dishwasher may not be connected to
open warm water devices or flow-through
water heaters.
•
Do not use old or used water inlet
hose on the new product. Use the new
water inlet hose supplied with the
product.
•
Connect the water inlet hose directly
to the water tap. Pressure coming
from the tap should be minimum 0.3
and maximum 10 bars. If the water
pressure exceeds 10 bars, a pressure
relief valve should be installed in
between.
•
Open the taps completely after making
the connections to check for water
leaks.
C
Use a screw-on hose connector
to connect the water inlet hose
to a water tap with a ¾ inch
external thread. If required, use
a filter insert to filter deposits
from the pipes.
A
For your safety, close the water
inlet tap completely after the
washing programme is over.
Water discharge hose can directly be
connected to the drain hole or sink’s
drainage. The length of this connection
must be min. 50 cm and max. 100 cm from
the floor. A discharge hose longer than 4
meters causes dirty washing.
Attach the water discharge hose to the
drainpipe without bending it. Tightly fix
the water discharge hose to the drainpipe
in order to prevent any dislocation of the
water discharge hose during operation of
the product.
min 300
min 120
max 1000
min 500
C
Drainpipe must be connected
to the sewage system and it
should not be connected to any
surface water.
If the door of the product cannot be closed
properly or if the product swings when you
push it slightly, then you need to adjust
the feet of the product. Adjust the feet of
the product as illustrated in the installation
manual supplied with the product.
Installation
•
The voltage and allowed fuse or breaker
protection are specified in the “Technical
specifications” section. If the current
value of the fuse or breaker in the house
is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
•
The specified voltage must be equal to
your mains voltage.
•
Do not make connections via extension
cables or multi-plugs.
B
Damaged power cables must
be replaced by the Authorised
Service Agent.
B
If your dishwasher is equipped
with internal illumination, lamp
should only be replaced by the
Authorised Service Agent in
case of failures that may occur
on the lamp.
B
If the product has a failure, it
should not be operated unless
it is repaired by the Authorised
Service Agent! There is the risk
of electric shock!
Before starting to use the product, make sure
that all preparations are made in accordance
with the instructions in sections “Important
safety instructions” and “Installation”.
• To prepare the product to do the dishes,
perform first operation in the shortest
programme with detergent while the
machine is empty. During the initial use,
fill the salt reservoir with 1 litre of water
prior to filling it with salt.
A
There might be a small amount
of water left in the product
after factory quality control
tests. This has no harm on the
product.
A
(depends on model)
The A system protects against
water leaks that may occur at the hose
inlet.Water contact with the valve box of
the system must be avoided to prevent
damage to the electrical system. If the
A system is damaged, unplug the
product and call the Authorised Service
Agent.
A
As the hose set contains
electrical connections and
assemblies, never shorten
or lengthen the hose with
extension hoses.
Connect the product to a grounded outlet
protected by a fuse complying with the
values in the “Technical specifications”
table. Our company shall not be liable for
any damages that will arise when the
product is used without grounding in
accordance with the local regulations.
• Connection must comply with national
regulations.
• Power cable plug must be within easy
reach after installation.
B
Unplug the product after the
washing programme is over.
10 11