background image

 

Page 6

Wireless Weather Station

 

7. Open the sensor array field case with a flat-bladed screwdriver and apply one of the 

power options indicated below.  

 

If you have a solar-powered system, connect the gel cell battery.  
If you have a non-solar-powered system, decide whether you want to install 
the power adapter OR the lithium battery (the two will NOT work in tan-
dem or as backup).  Davis recommends the battery to ensure power during 
storms.  If used as the primary power source, one 

 

fresh

 

 lithium battery 

should provide about six months of service.  Use two 

 

fresh

 

 lithium batteries 

to double life (second is not provided).  

 

Note:

 

Be sure dip switch #4 is set to “Run” (rather than “Test”) so that the LED indicator will not 
flash unnecessarily when not testing see “Testing Proposed Locations” on page 8 for instructions 

 

on setting dip switches).

 

Once power is applied, the console should start reading the values of the 
sensors installed in the sensor array.

SensorLink

Transmitter

Power

Plug

Gel Cell Battery

* Provided with solar systems
* Rechargeable 
* Recommended for solar-powered stations
* Reliable power during storms

2nd Lithium Battery (optional, not provided)

Power Adapter

* Provided with non-solar systems
* NOT RECOMMENDED for use during storms -
   power outages will disrupt data collection
   
  

Lithium Battery

* Provided with non-solar systems 
* RECOMMENDED - reliable power during storms

Содержание Weather Monitor II

















Отзывы: