background image

Troubleshooting

13

Problems Using Two Transmitting Stations

A single Vantage Vue console can receive signals from one sensor suite, either a Vantage Vue 

or a Vantage Pro2 sensor suite, and an optional anemometer transmitter kit. Make sure the 
transmitter IDs are configured correctly. See your 

Vantage Vue Console Manual

 for 

information on configuring transmitter IDs.

Most Common Rain Collector Problem

“My rain data seems too low.”

If the rain collector seems to be under-reporting rainfall, clean the debris screen and 
tipping spoon module to clear out any debris. 

Most Common Anemometer Problems

“The wind cups are spinning but my console displays 0 mph.”

The wind cups may not be turning the shaft. Remove the cups from the anemometer by 
loosening the set screw. Put the cups back onto the shaft and make sure to slide them 
down the shaft as far as possible. Re-tighten the set screw.

“The wind cups don’t spin or don’t spin as fast as they should.”

The anemometer may be located where wind is blocked by something, or there may be 
friction interfering with the cups’ rotation. Remove the wind cups by loosening the set 
screw, and clear out any insects or debris which may be interfering with the cup rotation. 
Turn the shaft the cups rotate on. If it feels gritty or stiff, contact Davis Technical 
Support.

Note: 

Do not lubricate the shaft or bearings in any way. 

“Readings aren’t what I expected them to be.”

Comparing data from your sensor suite to measurements from TV, radio, newspapers, or 
a neighbor is NOT a valid method of verifying your readings. Readings can vary 
considerably over short distances. How you site the sensor suite and anemometer can 
also make a big difference. If you have questions, contact Davis Technical Support. 

Contacting Davis Instruments

If you have questions about the sensor suite or Vantage Vue system, or encounter problems 
installing or operating the weather station, please contact Davis Technical Support. 

Note: Please do not return items to the factory for repair without prior authorization.

Online

www.davisinstruments.com

See the Weather Support section for copies of user 
manuals, product specifications, application notes, 
software updates, and more. 

E-mail

[email protected]

Telephone

(510) 732-7814 
Monday - Friday, 7:00 a.m. - 5:30 p.m. Pacific Time. 

Содержание Vantage Vue 6242

















Отзывы: