9
Questions and Answers
I
The recorder display is blank or faint.
1. Check that the two batteries are installed correctly.
2. Check if batteries require replacement.
3. Check if display contrast adjusted is adjusted too low.
The recorder does not respond when the buttons are pressed.
1. The
Normal/Hold
switch maybe in
Hold
position. Move to
Normal
position.
Unable to make a recording.
1. The recorders memory is full or folder message counter is full.
The recorder does not stop recording in automatic record mode when
there is silence.
1. The Mic Sensitivity is set too high, or the background noise level may be
equal to the sound source being recorded. Try decreasing the Mic Sensi-
tivity until recording stops.
2. Manual record mode may have to be used instead of automatic record mode.
The recorder does not start recording in automatic record mode when
there is sound.
1. The
microphone
sensitivity
level is set too low, try increasing the level.
2. The level of the sound source is low. Get closer to the sound source.
3.
Try recording in manual record mode.
vance notice in order for you to make necessary modifications to
maintain uninterrupted service.
g) Should you experience trouble with this equipment, please contact
Daval Technologies LLC, PO Box 27, Chappaqua, New York, 10514,
Tel: 914-251-9220 for repair or warranty information. If the equipment
is causing harm to the telephone network, the telephone company
may request that you disconnect the equipment until the problem is
resolved.
WARNING:
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
h) Please follow instructions for repairing if any (e.g. battery replace-
ment section); otherwise do not alternate or repair any parts of device
except specified.
i) Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission or cor-
poration commission for information.
j)
NOTICE:
If your home has specially wired alarm equipment con-
nected to the telephone line, ensure the installation of this
US:RNAKXNANDDVTR-680
equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equip-
ment, consult your telephone company or a qualified installer.
NOTICE:
According to telephone company reports, AC electrical
surges, typically resulting from lightning strikes, are very destructive
to telephone equipment connected to AC power sources. To minimize
damage from these types of surges, a surge arrestor is recommended.
Applicable for Coin or Pay Phone Only
To comply with state tariffs, the telephone company must be given
notification prior to connection for customer-owned coin or credit card
phone. In some states, the state public utility commission, public ser-
vice commission or corporation commission must give prior approval
of connection.
This equipment complies with Part 68 of the FCC Rules and the re-
quirements adopted by the ACTA. On the
bottom
of this equipment
is a label that contains, among other information, a product identifier
in the format
US:AAAEQ##TXXXX
.
If requested, this number must
be provided to the telephone company.
b) An applicable certification jacks Universal Service Order Codes
(USOC) for the equipment is provided (i.e.,
RJ11C
) in the packaging
with each piece of approved terminal equipment.
c) A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable FCC
Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
d) The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line
may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five
(5.0). To be certain of the number of devices that may be connected
to a line, as determined by the total RENs, contact the local tele-
phone company. For products approved after July 23, 2001, the REN
for this product is part of the product identifier that has the format
US:AAAEQ##TXXXX
. The digits represented by ## are the REN
without a decimal point (e.g., 03 is a REN of 0.3). For earlier prod-
ucts, the REN is separately shown on the label.
e) If this DVTR-680 equipment cause’s harm to the telephone net-
work, the telephone company will notify you in advance that tempo-
rary discontinuance of service may be required. But if advance no-
tice isn't practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
f) The telephone company may make changes in its facilities, equip-
ment, operations or procedures that could affect the operation of the
equipment. If this happens the telephone company will provide ad-
FCC Statement
J
Care and Maintenance
H
Your DVTR-680 Digital Voice Tele-Recorder
®
is designed to give years of
trouble free service. Please read the following maintenance instructions.
1. Keep the recorder dry. If it gets wet, wipe it dry immediately. Liquids can
contain minerals that can corrode the electronic circuits.
2. Handle the recorder gently and carefully. Dropping it can damage the
circuit boards which can cause it to malfunction
3. Store recorder in normal temperatures. Temperature extremes can
shorten the life of electronic devices and distort or melt plastic parts.
4. Wipe the recorder with a damp cloth to keep it looking new.
5. Do not use harsh chemicals, cleaning solvents, or strong detergents to
clean the recorder.
6. Use fresh batteries, old or weak batteries can leak chemicals that can
destroy electronic circuits.
