manualshive.com logo in svg

Dateq BCS50, Руководство пользователя

Поделиться
Скачать
Dateq BCS50 Скачать руководство пользователя страница 38

EN

DATEQ BCS50 user manual

BCS50 Technical specifications

37

BCS121 jumpers

Jumper

On/Off

Function

J1

ON

BCS121 configured as slave (using another Dateq clock/timer-unit as master)

OFF

BCS121 configured as master (default)

ON

12-hour time format with AM/PM (default in the USA)

OFF

24-hour time format (default in Europe)

J2

(not used)

J3

A0 = 0
A1 = 1

Address 0 remote control (default)

A0 = 1
A1 = 0

Address 1 remote control (when using multiple Dateq clock/timer-units in one
room, it is recommended to use different remote control addresses)

A0 = 0
A1 = 1

Address 2 remote control

A0 = 1
A1 = 1

Address 3 remote control

BCS121 antenna

The cable of the supplied DCF77-antenna can be extended without any problem (up to a
maximum of 100 meters, 300 feet). Mount the aerial in a position where reception quality of
the DCF77-transmitter is good. Be aware of the fact that the direction of the antenna is
important. If the reception of the transmitter is good, the LED on the aerial will blink every
second on a regular basis. If the LED doesn't blink, or blinks irregularly, reception is bad. The
cause for a bad reception can often be found in computer-equipment nearby, or steel
constructions in the building, blocking the long-wave signal of the transmitter.

CAUTION:

The supplied antenna is not suitable for outside-mounting. The antenna is not

waterproof, and the built-in electronic circuit will not operate properly below the freezing point
and above 50 degrees Celsius.

R26

R20

R19

L1

C6

C7

C8

+

C5

R25

1

+

C9

Q3

Q4

R24

U8

U9

1

1

1

1

1

1

2

Q1

U10

XT1

1

U12

R22

P12.

1

Q2

P13.

1

R21

J3

U13

3

1

P9

+

C23

R36

R37

R38

R39

R35

C20

C19

C18

C22

C16

C21

U16

R44

C4

4

1

1

U14

U17

J1

U15

D1

R42

J2

U18

R40

R41

+

C10

D3

L2

C11

C17

R43

U11

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

ON

OF

A0

A1

ADRESS

RC5-

0

1

P2

P3

P4

P5

P6

P7

P8

P10

P1

P11

8

REM1

REM2

REM3

REM4

REM5

REM6

REM7

RC5-ADRES

J1/J2/J3

Содержание BCS50









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды