manualshive.com logo in svg

Dateq BCS50, Руководство пользователя, Страница: 10 / 40

Поделиться
Скачать
Dateq BCS50 Скачать руководство пользователя страница 10

EN

DATEQ BCS50 user manual

BCS51(E) general

9

LowCut

The built-in LowCut crossover frequency is switchable between 20Hz and 80Hz. The filters
slope is 12dB/octave. This filter is to prevent annoying blobs from a microphone.

Tone control

Tone control is only available on a BCS51E module. The crossover frequencies are:

HIGH:

+/-12dB shelving @ 12 kHz

MID:

+/- 12dB bell @ 1.5 kHz

LOW:

+/- 16dB shelving @ 60 Hz

Jumper settings

With the internal jumpers various settings/ automations can be enabled or disabled. The
drawing below shows a PCB with the jumpers marked grey. In the table the functions are
described.

Jumper name

Possibilities

Description

CUE (1)

FADER (D)

The channel is activated when the fader is opened.

SWITCH

The channel is activated when the ON-key is pressed. When the fader
is opened and the ON-lamp does not light up no audio will be fed
through.

AUX (2)

POST (D)

The after-fader signal is routed to the AUX-buss. Both jumpers (P6
and P7) have to be in the same position!

PRE

The pre-fader signal is routed to the AUX-buss. Both jumpers (P6 and
P7) have to be in the same position!

ON-AIR (3)

OFF

No ON-AIR outputs will be activated when the channel is switched on.

ON-AIR1 (D)

When the channel is switched on ON-AIR1 will be activated. The
studio output will be muted to prevent an acoustical feedback.

ON-AIR2

When the channel is switched on ON-AIR2 will be activated.

MSTR (4)

ON (D)

When the PFL-switch is pressed the CR will switch automatically to
PFL. This makes the signal directly audible for the technician.

OFF

The signal is mixed to the PFL-buss, but the CR-selector will not
automatically switch to PFL.

DJ (5)

ON

When the module is activated all PFL-buttons will reset and the CR
output will be muted to prevent an acoustical feedback with the DJ-
microphone. It is also possible to let the CR-selector switch to AIR or
PGM. This will be explained on page 29.

OFF (D)

This function is disabled.

PHANTOM (6)

ON (D)

The phantompower (48V) is applied to the microphone-input. This is
necessary when using condenser microphones. Check your
microphones manual for more details.

OFF

The phantompower is disabled.

(D) indicates the default setting

1

2

3

4

5

6

Содержание BCS50









































Отзывы:

Нет отзывов