Datavideo CCU-200 Скачать руководство пользователя страница 3

 

- 2 - 

FCC Compliance Statement 

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions: 

1.

 

This device may not cause harmful interference, and  

2.

 

This device must accept any interference received, including interference that may cause 
undesired operation.

 

Warnings and Precautions 

1.

 

Read all of these warnings and save them for later reference. 

2.

 

Follow all warnings and instructions marked on this unit. 

3.

 

Unplug  this  unit  from  the  wall  outlet  before  cleaning.  Do  not  use  liquid  or  aerosol 
cleaners. Use a damp cloth for cleaning. 

4.

 

Do not use this unit in or near water. 

5.

 

Do  not  place  this  unit  on  an  unstable  cart,  stand,  or  table.  The  unit  may  fall,  causing 
serious damage. 

6.

 

Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To 
ensure safe and reliable operation of this unit, and to protect it from overheating, do not 
block  or  cover  these  openings.  Do  not  place  this  unit  on  a  bed,  sofa,  rug,  or  similar 
surface, as the ventilation openings on the bottom of the cabinet will be blocked. This 
unit should never be placed near or over a heat register or radiator. This unit should not 
be placed in a built-in installation unless proper ventilation is provided. 

7.

 

This product should only be operated  from the type of power source indicated on the 
marking  label  of  the  AC  adapter.  If  you  are  not  sure  of  the  type  of  power  available, 
consult your Datavideo dealer or your local power company. 

8.

 

Do  not  allow  anything  to  rest  on  the  power  cord.  Do  not  locate  this  unit  where  the 
power cord will be walked on, rolled over, or otherwise stressed. 

9.

 

If an extension cord must be used with this unit, make sure that the total of the ampere 
ratings  on  the  products  plugged  into  the  extension  cord  do  not  exceed  the  extension 
cord rating. 

10.

 

Make  sure  that  the  total  amperes  of  all  the  units  that  are  plugged  into  a  single  wall 
outlet do not exceed 15 amperes. 

11.

 

Never  push  objects  of  any  kind  into  this  unit  through  the  cabinet  ventilation  slots,  as 
they may touch dangerous voltage points or short out parts that could result in risk of 
fire or electric shock. Never spill liquid of any kind onto or into this unit. 

12.

 

Except as specifically explained elsewhere in this manual, do not attempt to service this 
product  yourself.  Opening  or  removing  covers  that  are  marked  “Do  Not  Remove”  may 
expose you to dangerous voltage points or other risks, and will void your warranty. Refer 
all service issues to qualified service personnel. 

13.

 

Unplug this product from the wall outlet and refer to qualified service personnel under 
the following conditions: 
a.

 

When the power cord is damaged or frayed; 

Содержание CCU-200





























Отзывы: