Datamax H-Class GPI O Option, Инструкция по эксплуатации

Страница: 7 / 14

5
W ARN I N G
Failure t o properly configure t he GPI O Port can result in dam age t o t he print er and / or connect ed devices.
GPI / O Por t A Ju m pe r Ove r vie w
Pin
Sign a l
N a m e
D ir e ct ion
[ 1]
Ju m pe r Posit ion Fu n ct ion / D e scr ipt ion
I nst alled Print er chassis is used.
1
Ground JMP 8
Rem oved Ground m ust be supplied.
I nst alled
Print er + 5VDC is used ( .5 am p m axim um )

N ot e : Drawing m ore t han .5 am ps can cause unreliable print er operat ion.
2 + 5 VDC
N/ A
JMP 9
Rem oved + 5VDC m ust be supplied.
3 St art Of Print
[ 2]
Program m able
[ 3]
4 Slew Label
Media is advanced unt il t he signal goes HI GH and, if not in cont inuous m ode, t he label
is posit ioned at t he next available TOF.
5 Toggle / Pause The print er pauses when t he signal is t aken LOW.
6 Reprint
I nput
The last label is reprint ed exact ly, wit h no increm ent or t im e st am p changes;
recom m ended for use during error condit ions. Keeping t his signal LOW produces non-
st op print ing.
7 + 24 VDC Print er + 24 VDC ( 1.5 am p m axim um ) .
8 Ground
N/ A
N/ A N/ A
Print er chassis.
9 Ribbon Low Program m able
[ 1]
. Signifies a RI BBON LOW DI AMETER warning condit ion.
10 Service Required Evoked by occurrences list ed under ‘Fault Messages.’
[ 1]
Act ive LOW.
11 End Of Print Program m able
[ 1]
. Signifies t he End of Print ( EOP) process.
12 Media Out Evoked during an Out of St ock condit ion. Act ive LOW.
13 Ribbon Out Evoked during an Out of Ribbon condit ion. Act ive LOW.
14 Dat a Ready
Evoked when a label is wait ing t o print . Aft er St art of Print is received, print ing will begin.
For synchronizat ion wit h t he print cycle, End Of Print indicat es t he com plet ion of t he
process. Act ive LOW.
15 Opt ion Fault
Out put JMP 1
When inact ive, out put s will be
pulled up t o a volt age
det erm ined by t his j um per
set t ing, where:

Pins 1 – 2 = + 5VDC;

Pins 2 – 3 = + 24VDC; or,

None = an ext ernal volt age
( not t o 30VDC) via
ext ernal pull- ups providing a
20K ohm feedback pat h
t hrough any t wo out put s.
Evoked during a Linear Scanner or RFI D fault condit ion. Act ive LOW.
[ 1]
Signal direct ions given relat ive t o t he print er.
[ 2]
I f act ive wit h no current print j ob, “ WAI TI NG FOR DATA” will be displayed. Specifying a quant it y of 9999 while keeping t his signal ON will cause non- st op label print ing, except
in single label “ I m aging Mode” , which will cause t he print er t o st op bet ween labels. See t he
Operat or’s Manual for det ails.
[ 3]
For det ails see PRI NTER OPTI ONS / GPI O PORT in t he Operat or’s Manual.