TL50
Contrast sensor
INSTRUCTION MANUAL
CONTROLS
OUT LED (yellow)
The yellow LED indicates the output status.
READY LED (green)
During functioning, the green LED permanently ON
indicates a normal operating condition; fast blinking
indicates an output overload condition.
DELAY LED (orange)
The orange LED ON indicates the timing function
activation on the digital output.
MARK PUSH-BUTTON
The mark detection procedure is activated by pressing
MARK push-button.
BKGD PUSH-BUTTON
The background detection procedure is activated by
pressing BKGD push-button.
See the “SETTING” paragraph for setup procedure
indications.
INSTALLATION
The sensor can be positioned using threaded M5 holes with max. 6 mm
depth.
Do not apply excessive torque when adjusting (max 2.2 Nm).
The
operating distance is measured starting from the front surface of the
sensor optics.
The reading direction can be changed inverting the cap and lens.
Mark detection on a reflective surface is improved adjusting the beam
direction to 5° … 20° from surface axis.
CONNECTIONS
SETTING
DETECTION (MARK-BACKGROUND)
-
Position mark in front of the sensor light spot and
press MARK push-button until the READY LED
(green) turns OFF.
The sensor detects the mark alternating the red,
green and blue emissions.
Avoid mark movements during this phase.
- Position the background in front of the sensor light
spot and press BKGD push-button; the sensor
detects the mark alternating the red, green and
blue emissions. Avoid background movements
during this phase.
The DARK/LIGHT operating mode is automatically
selected by the sensor.
Dark mark - light background = Dark mode.
Light mark - dark background = Light mode.
If the READY LED (green) is permanently ON, the
detection is successful.
If the LED blinks slowly, the detection has failed due
to insufficient contrast.
The sensor returns to the previous setting by pressing one of the two push-
buttons.
DELAY SETTING
The DELAY extends to 20ms the minimum duration of the active output
allowing the slower interfacing systems to detect shorter pulses.
The active delay is signalled by the corresponding orange LED ON.
Delay activation
Press MARK and BKGD push-buttons contemporaneously
for 2 sec. until the DELAY LED turns ON.
Delay deactivation
Press MARK and BKGD push-buttons contemporaneously
for 2 sec. until the DELAY LED turns OFF.
OUTPUT OVERLOAD
The digital output overload is signalled by the rapid blinking of the READY
LED.
The sensors are NOT safety devices, and so MUST NOT be used in the safety control of the machines
where installed.
Datalogic S.r.l.
Via S. Vitalino 13 - 40012 Calderara di Reno - Italy
Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com
Helpful links at www.datalogic.com:
Contact Us,
Terms and Conditions,
Support
.
The warranty period for this product is 36 months. See General Terms and Conditions of Sales for
further details.
Under current Italian and European laws, Datalogic is not obliged to take care of product
disposal at the end of its life. Datalogic recommends disposing of the product in compliance with
local laws or contacting authorised waste collection centres.
© 2007- 2017 Datalogic S.p.A. and/or its affiliates
ALL RIGHTS RESERVED.
Without limiting the
rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a
retrieval system, or transmitted in any form or by any means, or for any purpose, without the express
written permission of Datalogic S.p.A. and/or its affiliates. Datalogic and the Datalogic logo are registered
trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All other trademarks
and brands are property of their respective owners. Datalogic reserves the right to make modifications
and improvements without prior notification.
826003273 Rev.D
DIMENSIONS
TECHNICAL DATA
Power supply:
10…30 VDC limit values - Class 2 (UL508)
Ripple:
2 Vpp max.
Current consumption
(output current excluded):
50 mA max. @ 24Vcc
Output:
1 PNP output 1 NPN output
Output current:
100 mA max.
Output saturation voltage:
2 V
Response time:
33
s
Switching frequency:
15 kHz
Delay:
0 / 20 ms selectable
(default configuration without delay)
Dark/light selection
automatic
Indicators:
OUT LED (yellow) / READY LED (green)/DELAY LED (orange)
Push-buttons:
MARK and BKGD push-buttons
DARK/LIGHT selection:
Automatic
(default configuration LIGHT mode)
Operating temperature:
-10 … 55 °C
Storage temperature:
-20 … 70 °C
Dielectric strength:
500 VAC 1 min., between electronics and housing
Insulating resistance:
>20 M
500 Vdc, between electronics and housing
Operating distance:
9 mm
Depth of field:
3 mm
Minimum spot dimension:
1.5x5 mm @ 9 mm
Emission type:
BLUE (465 nm) / GREEN (520 nm) / RED (630 nm) with automatic selection
Ambient light rejection:
According to EN 60947-5-2
Vibrations:
0.5 mm amplitude, 10 … 55 Hz frequency, for each axis (EN60068-2-6)
Shock resistance:
11 ms (30 G) 6 shock for each axis (EN60068-2-27)
Housing material:
ABS
Lens material:
PMMA
Mechanical protection:
IP67
Connections:
M12 4-pole connector
Weight:
90 g. max.
AtEx 2014/34/EU:
II 3G EX nA II T6 ; II 3D EX tD A22 IP67 T85°C
ON
OUT with DELAY
OFF
20ms 20ms
ON
OUT without DELAY
OFF
