Datalogic QuickScan QD24 series Скачать руководство пользователя

Страница: 12 / 314

Technical Support

QuickScan™ I QD24XX/QBT24XX/QM24XX

Manual Conventions

The following conventions are used in this document:
The symbols listed below are used in this manual to notify the reader of key issues or proce-

dures that must be observed when using the reader:

NOTE

Notes contain information necessary for properly diagnosing, repairing and operating the
reader.

CAUTION

The CAUTION symbol advises you of actions that could damage equipment or property.

Current versions of this Product Reference Guide (PRG), Quick Reference Guide (QRG), the Dat-

alogic Aladdin™ Configuration application, and any other manuals, instruction sheets and utili-

ties for this product can be downloaded from the website listed below. Alternatively, printed

copies or product support CDs for most products can be purchased through your Datalogic

reseller.

Technical Support

Datalogic Website Support

The Datalogic website (

www.datalogic.com

) is the complete source for technical support and

information for Datalogic products. The site offers product support, warranty information,

product manuals, product tech notes, software updates, demos, and instructions for returning

products for repair.

Reseller Technical Support

An excellent source for technical assistance and information is an authorized Datalogic reseller.

A reseller is acquainted with specific types of businesses, application software, and computer

systems and can provide individualized assistance.

Telephone Technical Support

If you do not have internet or email access, you may contact Datalogic technical support at

(541) 349-8283 or check the back cover of your manual for more contact information.

Содержание QuickScan QD24 series



























































































































































































































































































































Результаты поиска

Содержание QuickScan QD24 series

Отзывы:

Похожие инструкции для QuickScan QD24 series

Бренды по названию

Популярные бренды

Datalogic QuickScan QD24 series, Руководство по продукции

Результаты поиска

Содержание QuickScan QD24 series

Отзывы:

Похожие инструкции для QuickScan QD24 series

Бренды по названию

Популярные бренды