Datacom Systems VS-1200 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 54

Datacom Systems VS-1200 Series Скачать руководство пользователя страница 26

VS-1200 Data Acccess Switch

26

© 2009 Datacom Systems Inc

4.1.4.15 DELETE USER (DE US)

This command deletes users as shown:

DELETE USER (USERNAME)

Example: # DE US edituser

User edituser deleted

#

4.2

SERIAL Port Configuration (DB9)

Note

: Use of the

SERIAL

DB9 port, which is fairly simple and straight forward, is strongly

recommended for initial configuration of the hardware.

Once VS-1200 series connection is made to the

SERIAL

DB9 port, open the terminal emulation

application and create a connection with settings that fit your needs:

4.2.1

HyperTerminal

The following example utilizes Microsoft HyperTerminal. Any freely available terminal emulator may
be utilized, but please take note of the specific HyperTerminal setup settings if an alternate terminal
emulator is used.

HyperTerminal (terminal emulator) enter:

9600 bits per second
8 data bits
Parity none
1 stop bit
Flow control none

After completing review of the

Command Line Interface (CLI)

section and

Exercise - CLI setting

Ports

section, detailed IP Address configuration can be found in the

IP Address Configuration

section.

17

36

28

«
...
24
25
26
27
28
...
»

Содержание VS-1200 Series























































Отзывы:

Нет отзывов