background image

 

 

 

 

 

DT-ATSC-QAM-8V2 Manual 

Unpacking and Inspection 

Each unit is shipped from the factory tested. Ensure all items are removed from the container 

prior to discarding any packing material. 

Thoroughly inspect the unit for shipping damage with particular attention to connectors and 

controls. If there is any sign of damage to the unit or damaged or loose connectors contact your 

distributor right away. 

Installation 

System Installer must adhere to Article 820-40 of the NEC that provides guidelines for proper 

grounding and specifies that the cable ground shall be connected to the grounding system of 

the building, as close to the point of cable entry as possible. 

Introduction to DT-ATSC-QAM-8V2: ATSC-8VSB / QAM-B to QAM-B Trans-Modulator 

The DataTronix DT-ATSC-QAM-8V2 is a high quality 8VSB /Clear QAM to QAM Trans-

modulator. It was designed to allow system integrators to receive and process up to 8 individual 

8VSB (ATSC) / Clear QAM channels along with up to 56 sub channels, and easily convert these 

signals to produce a high-quality RF QAM distribution system. The DT-ATSC-QAM-8V2 is a 

highly flexible system allowing integrators to quickly receive, convert, and distribute high quality 

Digital QAM channels to their customers. 

Features 

  Accepts 8 RF inputs (ATSC-8VSB/QAM) 

  Allows for Up to 64 Output Programs 

  Allows User to “Cherry Pick” Desired Programs as Needed 

  Supports STD/HRC/IRC Formats 

  Supports Full Range of ATSC-8VSB/QAM Signals 

  Offers 8 Fully Independent RF QAM Outputs 

  Easy to Setup and Monitor with GUI 

  Front Panel LED Indicators  

  3 VCN Modes Supported 

  High Density 1RU Design 

 

System Parsing / Response Time: 

The initial System Parsing time will range from 4-6 minutes on average as the system identifies 

and populates the required parameters. As the user navigates the device's menu note that a 

small delay may occur in populating the data on the screen as the system is constantly 

performing system parsing and system house-keeping functions. 

 

Содержание DT-ATSC-IP-8V2























Отзывы: