Data Translation DT9816 Series Скачать руководство пользователя

Страница: 33 / 108

Wiring Signals to the Module

Preparing to Wire Signals

This section provides recommendations and information about wiring signals to a DT9816
Series module.

Wiring Recommendations

Keep the following recommendations in mind when wiring signals to a DT9816 Series
module:

• Follow standard ESD procedures when wiring signals to the module.

• Use individually shielded twisted-pair wire (size 16 to 26 AWG) in highly noisy electrical

environments.

• Separate power and signal lines by using physically different wiring paths or conduits.

• To avoid noise, do not locate the box and cabling next to sources that produce high

electromagnetic fields, such as large electric motors, power lines, solenoids, and electric
arcs, unless the signals are enclosed in a mumetal shield.

• Prevent electrostatic discharge to the I/O while the box is operational.

• Connect all unused analog input channels to analog ground.

Wiring Signals to the DT9816, DT9816-A, DT9816-S, or
DT9816-S-WTR Module

To wire signals to a DT9816, DT9816-A, DT9816-S, or DT9816-S-WTR module, use the screw
terminals on the module, shown in

Figure 5

Содержание DT9816 Series













































































































Результаты поиска

Содержание DT9816 Series

Отзывы:

Похожие инструкции для DT9816 Series

Бренды по названию

Популярные бренды

Data Translation DT9816 Series, Руководство пользователя

Результаты поиска

Содержание DT9816 Series

Отзывы:

Похожие инструкции для DT9816 Series

Бренды по названию

Популярные бренды