DAS DL-300E Скачать руководство пользователя страница 5

Страница: 5 / 57

TERMINAL DESCRIPTION

TERMINAL #

DESCRIPTION

Connect one side of zone 1 loop. Connect other side of loop to
common terminal 2. Open

or short causes alarm.

Common (-) Terminal.

Connect one side of zone 2 loop. Connect other side of loop to
common terminal 2. Open

or short causes alarm.

4-12

See Terminal Drawing and repeat the above sequence for zones 3
through 8.

13-14

Auxiliary power, regulated 12VDC. Maximum 700mA for all Auxiliary
power outputs.

15-26

See Terminal Drawing and continue above described hookup zones 9
through 16.

27-28

Auxiliary power, regulated 12VDC. Maximum 700mA for all Auxiliary
power outputs.

Earth Ground, connect to a cold water pipe, or 6 to 10 foot driven rod.

30-31

AC input, connect a 16.5V 50VA approved transformer.

32-33

Resettable 12VDC 250mA Aux power.(Memory reset and/or Smoke
detector power)

34-36

Form C programmable on board relay output. Tied to auxiliary output
#3.

Negative, provided as a convenience for relay connection.

38-39

Form A programmable on board relay output. Tied to auxiliary output
#4.

40-41

Siren driver output to speaker(s). Min speaker rating 30/40 watt at 4, 8,
or 16 ohms). See

page ? for connection diagram. When a 10/15 watt speaker is used,
connect one wire to

terminal 40 or 41 and the other wire to terminal 37.

42-45

Connect code pad wires as follows; Green to terminal 42, Yellow to
Terminal 43, Red to

terminal 44, and Black to terminal 45. Maximum run with 7/020 cable is
70 meters.

Maximum run with 14/020 cable is 120 meters. A maximum of 4 code
Pads may be

Connected.

Battery :Leads

Connect to 12VDC lead acid rechargeable battery: Black(-) & Red(+).
Do not use a dry cell

battery.

FUSE DESCRIPTION

Содержание DL-300E


























































Результаты поиска

Содержание DL-300E

Отзывы:

DAS DL-300E, Руководство по установке, Страница: 5 / 57

Результаты поиска

Содержание DL-300E

Отзывы: