DARLEY 2BE6.5H Скачать руководство пользователя страница 33

Страница: 33 / 35

Prepared by: TED

Rev. #: 13

Approved by: MCR

15May2006

1200569.doc

Engine Maintenance:

HONDA GX200 ENGINE MAINTENANCE REQUIREMENTS

SYSTEM ID

ACTION

INTERVAL

MNT LVL

SPARES REQUIRED/DWG NO.

TOOLS/SE
REQUIRED

PMS NUMBER

Engine/Fuel
System

Inspect fuel tank

Upon receipt, and each time
unit is operated

Unit

Fuel tank, p/n 4217707

Replace fuel tank assembly

Upon failure

Unit

Tank, Fuel, Assembly, p/n KE00109
(See dwg. #DGM1108)

Replace fuel tank

Upon failure

Unit

Tank, Fuel, 2.5 gal. plastic, p/n
4217707 (See dwg. #DGM1108)

Replace fuel tank mount bracket

Upon failure

Depot

Bracket, fuel tank mount, p/n 4025803
(See dwg. # DGM1108)

7/16” Open end wrench
½” Open end wrench

Replace poly tie down

Upon failure

Unit

Tie down, poly, p/n 4427100 (See
dwg. # DGM1108)

Replace fuel cap

Upon failure

Unit

Cap, Fuel Tank, p/n 4217712

Replace fuel gage

Upon failure

Unit

p/n 4217713

Check oil level

Prior to each use

Unit

4 stroke SAE 10W-30 detergent oil
(.63 U.S. qts.)

Change oil

First 20 hrs and 100 hrs/6 mos
thereafter

Unit

4 stroke SAE 10W-30 detergent oil
(.63 U.S. qts.)

10mm Socket

Check air filter

After every use.

Unit

n/a

Replace air filter

Every 300 hrs of ops

Unit

Air filter, Honda p/n 17210-ZE1-505

Replace fuel filter

Every 300 hrs. of ops

Unit

Fuel filter, Honda p/n 16910-ZE8-015
Fuel Filter, Darley p/n 4207201

Check fuel line

Quarterly

Unit

n/a

Replace fuel line

Upon failure

Unit

Hose, .25 x 1.75 fuel, p/n 4402325
(See dwg. #DGM1109)

Pliers

Check high speed adjustment

Yearly Unit

n/a

Hand

Tachometer

Clean sediment cup

Every 100 hrs., or 6 mos., or
during every oil change

Unit n/a

10mm

Socket

High flash-point solvent

Clean fuel tank

Yearly or every 300 hrs.

Unit

n/a

Check spark plug

Every 100 hrs. or 6 mos.

Unit

n/a

13/16" Deep socket

Replace plug

Upon failure

Unit

NGK #BPR6ES or equivalent

13/16" Deep socket

Check/readjust valve clearance

Every 300 hrs. or 1 yr.

Unit

n/a

Clean carburetor

As necessary

Unit

n/a

10mm Socket
High flash-point solvent

Remove corrosion

As needed

Unit

n/a

Silicone grease,
High flash point solvent,
paint, etc.

Содержание 2BE6.5H




































Результаты поиска

Содержание 2BE6.5H

Отзывы:

Похожие инструкции для 2BE6.5H

Бренды по названию

Популярные бренды

DARLEY 2BE6.5H, Руководство оператора

Результаты поиска

Содержание 2BE6.5H

Отзывы:

Похожие инструкции для 2BE6.5H

Бренды по названию

Популярные бренды