background image

 

 

Do not connect this system to a dimmerpack. 

 

Do not switch the system on and off in short intervals, as this would reduce the system’s life. 

 

Do not open the device and do not modify the device. 

 

Do not drive the inputs with a signal level bigger, than required to drive the equipment to full 
output. 

 

Only use system indoor, avoid contact with water or other liquids. 

 

Avoid flames and do not put close to flammable liquids or gases. 

 

Always disconnect power from the mains, when system is not used. Only handle the power-cord 
by the plug. Never pull out the plug by tugging the power-cord. 

 

Always operate the unit with the AC ground wire connected to the electrical system ground. 

 

Make sure you don’t use the wrong kind of cables or defective cables. 

 

Make sure that the signals from the mixer are balanced, otherwise hum could be created. 

 

Make sure that the available voltage is not higher than stated on the rear panel.  

 

Make sure that the power-cord is never crimped or damaged. Check the system and the power-
cord from time to time. 

 

Please turn off the power switch, when changing the power cord or signal cable. 

 

Extreme frequency boosts in connection with a high input signal level may lead to overdriving 
your equipment. Should this occur, it is necessary to reduce the input signal level by using the 
INPUT control. 

 

To emphasize a frequency range, you don’t necessarily have to move its respective control 
upward; try lowering surrounding frequency ranges instead. This way, you avoid causing the next 
piece of equipment in your sound path to overdrive. You also preserve valuable dynamic reserve 
(“headroom”) 

 

Avoid ground loops! Always be sure to connect the power amps and the mixing console to the 
same electrical circuit to ensure the same phase! 

 

If system is dropped or struck, disconnect mains power supply immediately. Have a qualified 
engineer inspect for safety before operating. 

 

If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do 
not switch it on immediately. The arising condensation water might damage your system. Leave 
the system switched off until it has reached room temperature. 

 

If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit 
securely (preferably in the original packing material), and return it to your Dap Audio dealer for 
service. 

 

Repairs, servicing and electric connection must be carried out by a qualified technician. 

 

For replacement use fuses of same type and rating only. 

 

WARRANTY: Till one year after date of purchase. 

 
 

OPERATING DETERMINATIONS 

 

This system is not designed for permanent operation. Consistent operation breaks will ensure that the 
system will serve you for a long time without defects. 
 
If this system is operated in any other way, than the one described in this manual, the product may suffer 
damages and the

 

warranty becomes void.  

Any other operation may lead to dangers like short-circuit, burns, electric shock, etc. 
 
You endanger your own safety and the safety of others! 

 

Improper installation can cause serious damage to people and property !

 

 

 

 

 

Содержание LT-215A


















Отзывы: