Dantherm 351510 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 55

background image

45

EN

Evaporator sensor fail

If evaporator sensor is defect, then “EVAP” code will be shown when pressing UP or DOWN
during screen shows Sensor fail code “SEnS”.
If Evaporator sensor ok, then no “EVAP” code shall be shown.
If no buttons pressed within 10 seconds then screen will show “SEnS” fail again.
It is not possible to enter menu setup to modify set point.

RH/T sensor fail

If RH/T sensor is defect, then “rh°t” code will be shown when pressing UP or DOWN during

screen shows Sensor fail code “SEnS”.
If RH/T sensor ok, then no “rh°t” code shall be shown.
If no buttons pressed within 10 seconds then screen will show “SEnS” fail again.
It is not possible to enter menu setup to modify set point.

Low pressure fail

Dehumidifier stopped because of Low Pressure detection.
Fail can not be dismissed from DRC1.
It is not possible to enter menu setup to modify set point.

Alarms continued

Press to see which sensor
is defect.

Press to see which sensor
is defect.

Press to see which sensor
is defect.

Press to see which sensor
is defect.

«
...
43
44
45
46
47
...
»

Содержание 351510
























































Отзывы:

Нет отзывов

Похожие инструкции для 351510

Бренд: Wood’s Страницы: 7

Бренд: Rowenta Страницы: 20

Бренд: Quincy Compressor Страницы: 16

Бренд: Woods Страницы: 4

Бренд: TCL Страницы: 42

Бренд: Holmes Страницы: 2

Бренд: BRAYER Страницы: 31

Бренд: Essick Страницы: 12

Бренд: Essick Страницы: 10

Бренд: Essick Страницы: 10

MoistAIR MA1201

Бренд: Essick Страницы: 32

Бренд: Trident Страницы: 41

Бренд: Ideal Air Страницы: 7

Dri-Eaz PHD 200

Бренд: Legend Brands Страницы: 27

Бренд: N'oveen Страницы: 39

Бренд: Desa Страницы: 144

Бренд: Skuttle Indoor Air Quality Products Страницы: 12

Бренд: Stadler Form Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды