background image

 Single compressors

Installation

High voltage test

For brazing the suction and discharge 
connections, the following procedure is advised:
• Make sure that no electrical wiring is connected 

to the compressor.

• Protect painted surfaces on the terminal box 

and compressor from torch heat damage (see 
diagram).

• Remove the Teflon gaskets when brazing 

rotolock connectors with solder sleeves.

• Use only clean, refrigeration-grade copper 

tubing and clean all connections.

• Use brazing material with a minimum of 5% 

silver content.

• Purge nitrogen or CO

2

 through the compressor 

in order to prevent against oxidation and 
flammable conditions. The compressor should 
not be exposed to the open air for extended 
periods.

• Use of a double-tipped torch is recommended.
• Apply heat evenly to area A until the brazing 

temperature is reached. Move the torch to 
area B and apply heat evenly until the brazing 
temperature has been reached there as well, 
and then begin adding the brazing material. 
Move the torch evenly around the joint, in 
applying only enough brazing material to flow 
the full circumference of the joint.

• Move the torch to area C only long enough to 

draw the brazing material into the joint, but not 
into the compressor.

• Remove all remaining flux “once the joint has 

been soldered” with a wire brush or a wet cloth. 
Remaining flux would cause corrosion of the 
tubing.

Ensure that no flux is allowed to enter into the 
tubing or compressor. Flux is acidic and can cause 
substantial damage to the internal parts of the 
system and compressor.

The polyolester oil used in VZH compressors 
is highly hygroscopic and will rapidly absorb 
moisture from the air. The compressor must 
therefore not be left open to the atmosphere 
for a long period of time. The compressor fitting 
plugs shall be removed just before brazing the 
compressor. The compressor should always be 
the last component brazed into the system 

Before eventual unbrazing the compressor or 
any system component, the refrigerant charge 
must be removed from both the high- and 
low-pressure sides. Failure to do so may result in 
serious personal injury. Pressure gauges must be 
used to ensure all pressures are at atmospheric 
level.

For more detailed information on the appropriate 
materials required for brazing or soldering, please 
contact the product manufacturer or distributor. 
For specific applications not covered herein, 
please contact Danfoss for further information.

Carry out a high voltage test by short-circuiting 
terminals U, V, W, L1, L2 and L3. Energize by max. 
1920 V DC for code G compressors and 1460 V DC 
for code J compressors for one second between 
this short-circuit and the chassis. When running 
high voltage tests of the entire installation, 
frequency converter and compressor electrical 

motor compressor test can be conducted 
together. When conducting a high voltage test 
make sure the system is not under vacuum: this 
may cause electrical motor compressor failure. 
Please note, it is note recommended that a high-
voltage test be carried out too often as it may 
damage the motor.

38

FRCC.PC.034.A2.02

Application Guidelines

Содержание VZH Series

















































Отзывы: