Danfoss VLT Soft Starter MCD 600 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 34

Danfoss VLT Soft Starter MCD 600 Скачать руководство пользователя страница 7

2 Introduction

2.1 Product Design

The EtherNet/IP Card allows the soft starter to connect to an Ethernet network and be controlled or monitored using an Ethernet
communication model.
Familiarity with Ethernet protocols and networks is required to operate the device successfully. For difficulties arising from using
this device with 3

rd

-party products, including PLCs, scanners, and commissioning tools, contact the relevant supplier.

2.2 Compatibility

This communication expansion card is suitable for use with VLT® Soft Starter MCD 600.
This Installation Guide is intended for use with version 2.x of the VLT® Soft Starter MCD 600 EtherNet/IP Card. Version 1.x of the
EtherNet/IP Card does not support custom users, TCP connection, or IoT operation.

2.3 Network Connection

Table 1: Supported Protocols

Protocols

EtherNet/IP

Industrial Ethernet via EtherNet/IP

TCP

Transmission control protocol to connect to port 4000 of a PC

MQTT

Message queue telemetry transport

OPC UA

Open platform communications unified architecture

4/T2

READY

RUN

TRIP

LOCAL

Exit

Reset

Menu

Store

2/T1

6/T3

1/L1

3/L2

5/L3

VLT

®

Soft Starter

1

2

4

3

5

e7

7h

a8

05

.1

0

Illustration 1: Overview of Network Connections

1

Soft starter

2

Network switch

3

IoT connection (MQTT/OPC UA)

4

Industrial Ethernet connection to programmable
logic controller

5

TCP connection to VLT® Motion Control Tool MCT
10. Refer to the VLT® Motion Control Tool MCT 10
Operating Guide for connection details.

AN353423548483en-000101 / 130R0945 | 7

Danfoss A/S © 2020.12

Introduction

EtherNet/IP Card

Installation Guide

«
...
5
6
7
8
9
...
»

Содержание VLT Soft Starter MCD 600



































Отзывы:

Нет отзывов