Parameter
Range
Default
Function
0-03 Regional Settings
[0] International
[1] US
0
0-06 GridType
[0] -[[132] see start -up wizard
for open loop application
Size selected
Select operating mode for restart upon
reconnection of the frequency converter to
mains voltage after power down.
1-00 Configuration Mode
[0] Open loop
[3] Closed loop
0
Change this parameter to Closed loop.
1-20 Motor Power
0.09-110 kW
Size related
Enter motor power from nameplate data.
1-22 Motor Voltage
50.0-1000.0 V
Size related
Enter motor voltage from nameplate data.
1-23 Motor Frequency
20.0-400.0 Hz
Size related
Enter motor frequency from nameplate data.
1-24 Motor Current
0.0 -10000.00 A
Size related
Enter motor current from nameplate data.
1-25 Motor Nominal Speed
100.0-9999.0 RPM
Size related
Enter motor nominal speed from nameplate
data.
1-26 Torque nominal do Motor
0.1-1000.0
Size related
This parameter is available only when
1-10 Construção do Motor Design is set to
[1]
PM, non-salient SPM
.
NOTE
Changing this parameter affects settings
of other parameters.
1-29 Automatic Motor Adaption
(AMA)
Off
Performing an AMA optimizes motor
performance.
1-30 Resistência do Estator (Rs)
0.000-99.990
Size related
Set the stator resistance value.
1-37 Indutância do eixo-d (Ld)
0-1000
Size related
Enter the value of the d-axis inductance.
Obtain the value from the permanent magnet
motor data sheet. The de-axis inductance
cannot be found by performing an AMA.
1-39 Pólos do Motor
2-100
4
Enter the number of motor poles.
1-40 Força Contra Eletromotriz em
1000RPM
10-9000
Size related
Line-Line RMS back EMF voltage at 1000 RPM.
1-73 Flying Start
[0] Disabled
[1] Enabled
0
Select
[1] Enable
to enable the frequency
converter to catch a spinning motor. I.e. fan
applications. When PM is selected, Flying Start
is enabled.
3-02 Minimum Reference
-4999-4999
0
The minimum reference is the lowest value
obtainable by summing all references.
3-03 Maximum Reference
-4999-4999
50
The maximum reference is the highest value
obtainable by summing all references.
3-10 Preset Reference
-100-100%
0
Enter the set point.
3-41 Ramp 1 Ramp Up Time
0.05-3600.0 s
Size related
Ramp up time from 0 to rated 1-23 Motor
Frequency if Asynchron motor is selected;
ramp up time from 0 to 1-25 Motor Nominal
Speed if PM motor is selected".
3-42 Ramp 1 Ramp Down Time
0.05-3600.0 s
Size related
Ramp down time from rated 1-23 Motor
Frequency to 0 if Asynchron motor is selected;
ramp down time from 1-25 Motor Nominal
Speed to 0 if PM motor is selected.
4-12 Motor Speed Low Limit [Hz]
0.0-400 Hz
0.0 Hz
Enter the minimum limit for low speed.
4-14 Motor Speed High Limit [Hz]
0-400 Hz
65 Hz
Enter the minimum limit for high speed.
4-19 Freqüência Máx. de Saída
0-400
Size related
Enter the maximum output frequency value.
6-29 Terminal 54 mode
[0] Current
[1] Voltage
1
Select if terminal 54 is used for current- or
voltage input.
6-20 Terminal 54 Low Voltage
0-10 V
0.07 V
Enter the voltage that corresponds to the low
reference value.
Quick Guide
VLT
®
HVAC Basic Drive Cascade Controller Quick Guide
18
MG18F402 - VLT
®
is a registered Danfoss trademark
1
1
