background image

5-13  Terminal 29 Digital Input

Parameter for configuring the input function on input terminal
29.

Option:

Function:

[64]

Counter B
(down)

[65]

Reset Counter
B

3.6.3 5-4* Relays

Parameters for configuring the timing and the output
functions for the relays.

5-40  Function Relay

Array (Relay 1 [0], Relay 2 [1])

Select options to define the function of the relays.
The selection of each mechanical relay is realized in an array
parameter.

Option:

Function:

[0]

No operation

Default for both relays.

[1]

Control Ready The control board receives supply

voltage.

[2]

Drive ready

The frequency converter is ready for
operation and applies a supply
signal on the control board.

[3]

Drive ready/
remote control

The frequency converter is ready for
operation in 

Auto On-

mode.

[4]

Standby / no
warning

The frequency converter is ready for
operation. No start or stop
command is given. No warnings are
present.

[5]

Drive running

The compressor runs.

[6]

Running / no
warning

The compressor runs, and no
warning are present.

[7]

Run in
range/no
warning

The compressor runs within
programmed current ranges, see 

parameter 4-50 Warning Current Low

and 

parameter 4-51 Warning Current

High

. No warnings are present.

[8]

Run on ref/no
warning

The compressor runs at reference
speed and with no warnings.

[9]

Alarm

An alarm activates output.

[10]

Alarm or
warning

An alarm or warning activates
output.

[12]

Out of current
range

The compressor current is outside
the range set in 

parameter 4-50 Warning Current Low

and 

parameter 4-51 Warning Current

High

.

5-40  Function Relay

Array (Relay 1 [0], Relay 2 [1])

Select options to define the function of the relays.
The selection of each mechanical relay is realized in an array
parameter.

Option:

Function:

[13]

Below current,
low

The compressor current is lower
than set in 

parameter 4-50 Warning

Current Low

.

[14]

Above current,
high

The compressor current is higher
than set in 

parameter 4-51 Warning

Current High

.

[16]

Below speed,
low

The frequency converter output
speed is lower than the limit set in 

parameter 4-40 Warning Freq. Low

.

[17]

Above speed,
high

The frequency converter output
speed is higher than the limit set in 

parameter 4-41 Warning Freq. High

.

[19]

Below
feedback, low

The feedback is lower than the limit
set in 

parameter 4-56 Warning

Feedback Low

.

[20]

Above
feedback, high

parameter 4-57 Warning Feedback
High

.

[21]

Thermal
warning

The thermal warning turns on when
the temperature exceeds the limit
in the compressor, frequency
converter, or thermistor.

[22]

Ready, no
thermal
warning

The frequency converter is ready for
operation and no overtemperature
warning is present.

[23]

Remote, ready,
no thermal
warning

The frequency converter is ready for
operation in 

Auto

 mode, and no

overtemperature warning is present.

[24]

Ready, Voltage
OK

The frequency converter is ready for
operation and mains voltage is
within specified voltage range.

[25]

Reverse

The compressor runs/is ready to run
clockwise when logic=0 and
counterclockwise when logic=1. The
output changes when the reversing
signal is applied.

[26]

Bus OK

Active communication (no timeout)
via serial communication port.

[35]

External
Interlock

See 

5-1* Digital Inputs

.

[36]

Control word
bit 11

Bit 11 in control word controls the
relay.

[37]

Control word
bit 12

Bit 12 in control word controls the
relay.

Parameters

VLT

®

 Compressor Drive CDS 803

32

Danfoss A/S © 06/2019 All rights reserved.

MG18P202

3

3

Содержание VLT CDS 803





























































































Отзывы: