Danfoss VLT CDS 803 Скачать руководство пользователя страница 26

Страница: 26 / 92

3-10 Preset Reference

Range:

Function:

selecting dedicated references,
select

preset reference bit 0/1/2 [16],

[17]

, or

[18]

for the corresponding

digital inputs in

parameter group

5-1* Digital Inputs

3-11 Jog Speed [Hz]

Range:

Function:

30 Hz

[ 0 - 500.0
Hz]

The jog speed is a fixed output
speed at which the frequency
converter is running when the jog
function is activated.
See also

parameter 3-80 Jog Ramp

Time

3-14 Preset Relative Reference

Define the fixed value in %.

Range:

Function:

0 %

[-100 -
100 %]

The sum of fixed and variable
values (labeled Y in

Illustration 3.3

)

is multiplied by actual reference
(labeled X in

Illustration 3.3

). This

product is added to actual
reference

X + X × Y

100

Relative

Z=X+X*Y/100

Resulting

actual

reference

130BA059.12

Illustration 3.3 Preset Relative
Reference

3-15 Reference 1 Source

Select the input to be used for the 1

reference signal.

Parameter 3-15 Reference 1 Source

parameter 3-16 Reference 2

Source

, and

parameter 3-17 Reference 3 Source

define up to 3

different reference signals. The sum of these reference signals
defines the actual reference.

Option:

Function:

[0]

No function

[1]

Analog Input
53

[2]

Analog Input
54

[7]

Pulse input 29

[11]

Local bus
reference

3-16 Reference 2 Source

Select the input to be used for the 2

reference signal.

Parameter 3-15 Reference 1 Source

parameter 3-16 Reference 2

Source

, and

parameter 3-17 Reference 3 Source

define up to 3

different reference signals. The sum of these reference signals
defines the actual reference. See also

parameter 1-93 Thermistor

Source

Option:

Function:

[0]

No function

[1]

Analog Input
53

[2]

Analog Input
54

[7]

Pulse input 29

[11]

Local bus
reference

3-17 Reference 3 Source

Select the reference input to be used for the 3

reference signal.

Parameter 3-15 Reference 1 Source

parameter 3-16 Reference 2

Source

, and

parameter 3-17 Reference 3 Source

define up to 3

different reference signals. The sum of these reference signals
defines the actual reference.

Option:

Function:

[0]

No function

[1]

Analog Input
53

[2]

Analog Input
54

[7]

Pulse input 29

[11]

Local bus
reference

3.4.3 3-4* Ramp 1

Configure the ramp time parameters for each of the 2
ramps (

parameter group 3-4* Ramp 1

and

parameter group

3-5* Ramp 2

). The ramp time is preset to the minimum

value of 10 ms for all power sizes.

acc

dec

130BB801.10

P 3-*2

Ramp (X)

Down

Time (Dec)

P 4-14

High-limit

RPM

Reference
P 1-23

Motor

frequency
P 4-12

Low limit

Time

P 3-*1

Ramp (X)Up

Time (Acc)

Illustration 3.4 Ramps

Parameters

VLT

Compressor Drive CDS 803

MG18P202

Содержание VLT CDS 803




























































































Результаты поиска

Содержание VLT CDS 803

Отзывы:

Похожие инструкции для VLT CDS 803

Бренды по названию

Популярные бренды

Danfoss VLT CDS 803, Руководство по программированию

Результаты поиска

Содержание VLT CDS 803

Отзывы:

Похожие инструкции для VLT CDS 803

Бренды по названию

Популярные бренды