5
VLT
®
3500 HVAC
MG.35.B1.02 – VLT is a registered Danfoss trademark
Section 1Section 1Section 1Section 1Section 1
Section 2Section 2Section 2Section 2Section 2
Section 3Section 3Section 3Section 3Section 3
Section 4Section 4Section 4Section 4Section 4
VL
VL
VL
VL
VLT type
T type
T type
T type
T type
3502
3502
3502
3502
3502 3504
3504
3504
3504
3504 3508
3508
3508
3508
3508 3511
3511
3511
3511
3511 3516
3516
3516
3516
3516 3522
3522
3522
3522
3522 3532
3532
3532
3532
3532 3542
3542
3542
3542
3542 3552
3552
3552
3552
3552 3562
3562
3562
3562
3562
Output current
I
VLT,N
[A]
5.4
10.6
24.8
32.0
46.0
61.2
88.0
104.0 130.0 154.0
I
VLT, MAX
(60 s) [A]
5.9
11.7
27.3
35.2
50.6
67.3
96.8
114.4 143.0 169.0
Output (at 230 V)
S
VLT,N
[kVA]
2.2
4.0
9.8
12.7
18.3
24.4
35.1
41.4
51.8
61.3
Typical shaft output
P
VLT,N
[kW]
1.1
2.2
5.5
7.5
11.0
15.0
22.0
30.0
37.0
45.0
Max. cable cross-section
[mm
2
]
2.5
2.5
16.0
16.0
16.0
35.0
50.0
70.0
70.0
70.0
Terminal torque
[Nm]
-
-
-
-
-
-
-
6
6
6
Max. motor cable length
[m]
300, with screened cables: 150 m f
SW
≤
4.5 kHz
Rated motor voltage
U
M,N
[V]
200/220/230
Rated motor frequency
f
M,N
[Hz]
50/60/87/100
Max. input current
I
L,N
[A]
5.4
10.6
23.1
29.6
42.0
56.8
72.3
102.0 128.0 152.0
Max. cable cross-section
[mm
2
]
2.5
2.5
16.0
16.0
16.0
35.0
50.0
120.0 120.0 120.0
Terminal torque
[Nm]
-
-
-
-
-
-
-
31.1
31.1
31.1
Max. pre-fuses
[A]
16.0
25.0
40.0
50.0
60.0
80.0
125.0
1
150.0
3
150.0
3
150.0
3
Mains contactor
4)
[Danfoss type]
CI 6
CI 12 CI 9
CI 16 CI 32 CI 32 CI37
CI 85 CI 85 CI 85
[AC value]
AC-3
AC-3
AC-1
AC-1
AC-1
AC-1
AC-1
AC-1
AC-1 AC-1
Supply voltage (VDE 0160)
[V]
3 x 200/220/230 ±10%
3 x 220/230/240 V
Supply frequency
[Hz]
50/60
Power factor / cos.
ϕ
1
0.9/1.0
Switching on input
times/min.
2
Power loss at
Front
-
-
-
-
-
-
-
357
394
409
max. load.
Heat sink
-
-
-
-
-
-
-
588
712
884
[W]
Total
60
130
425
580
651
929
1350
945
1106
1293
Ambient temperature
[°C]
-10
→
+40, operation at full load
2
)
1
)
Only semi-conductor fuses.
2
)
In the range -10 to 0°C, the equipment can start and run; however, the display values and
certain operating characteristics will not fulfil the specifications.
3
)
Bussmann rapid type JJS integrated.
4)
If mains contactors are used, the following Danfoss types are recommended:
Max. ambient tempe 40°C
Installation related product data
Mains supply 3 x 200/220/230 V or 3 x 220/230/240 V
According to international VDE and UL/CSA
requirements
2.1 Installation r
elated pr
oduct data
- 15%
+10%
Mechanical and electrical installation
■
■
■
