Danfoss PVG 32 Скачать руководство пользователя страница 32

Страница: 32 / 76

Fault monitoring overview

Type

Fault
monitoring

Delay before error
out

Error mode

Error output
status

Fault output
on PVE

LED light

Memory

†

PVEO
PVEM

No fault monitoring

PVEA
PVEH
PVEP
PVES
PVEU

Active

500 ms
(PVEA: 750 ms)

No fault

Low

< 2 V

Green

–

Input signal faults

High

Flashing red

Yes

Transducer (LVDT)

Constant red

Close loop fault

Passive

250 ms
(PVEA: 750 ms)

No fault

Low

< 2 V

Green

–

Input signal faults

High

Flashing red

Transducer (LVDT)

Constant red

Close loop fault

PVE
Float
six pin

Active

500 ms

Float not active

High

Constant red

Yes

750 ms

Float still active

Measured between fault output pin and ground.

†

Reset needed

PVEO

The PVEO is an on/off activated actuator. The PVEO has not fault-monitoring.

Variants:

•

PVEO-R with a ramp delayed actuation

•

PVEO-DI with direction indication feedback

•

Anodized aluminum block

•

ATEX certified

Power supply:

•

12 V

•

24 V

Connectors:

•

AMP

•

DIN/Hirshmann

•

Deutsch

AMP version

DIN/Hirschmann version

Deutsch

version

PVEO/PVEO-R

157-502.11

PVEM

The PVEM is a proportional activated actuator. The PVEM has not fault-monitoring.

Variants:

•

PVEM -R with a ramp delayed actuation

•

PVEM for float in B-direction and max. flow B at 4.8 mm

Power supply:

12 / 24 V

Connectors:

DIN/Hirshmann

Technical Information

PVG 32 Proportional Valve Group

Electrical actuation

32 |

Danfoss | August 2017

520L0344 | BC00000038en-US0802

Содержание PVG 32













































































Результаты поиска

Содержание PVG 32

Отзывы:

Похожие инструкции для PVG 32

Бренды по названию

Популярные бренды

Danfoss PVG 32, Техническая информация

Результаты поиска

Содержание PVG 32

Отзывы:

Похожие инструкции для PVG 32

Бренды по названию

Популярные бренды