Danfoss Performer SM Series Скачать руководство пользователя страница 35

Страница: 35 / 40

Discharge line

Insulation

Bracket

Thermostat

accessoRies

compressor model

attenuation*

(at 50Hz) dB(a)

Hood code number

SM / SZ 084 - 090 - 100

7755011

SM / SZ 110 - 120

8.5

7755010

SM / SZ 115 - 125

7755009

SM / SZ 160

7755008

SM / SZ 148 - 161**

7755017

SM / SZ 175 - 185

7755007

SY / SZ 240 - 300

7755016

SY / SZ 380

7755022

* Attenuation of compressor sound power level measured in free space

** Not available for code 3 version compressors

Discharge  gas  temperature  must  not
exceed 275°F.
The  discharge  gas  thermostat  acces-
sory  kit  includes  all  components
required  for  installation  as  shown
below.  The  thermostat  must  be

attached to the discharge line within
6” of the compressor discharge port.

Discharge thermostat kit code
number: 7750009.

Acoustic compressor hoods have been
developed to meet specific extra-low
noise requirements. These hoods

incorporate soundproofing materials
and offer excellent high and low
frequency attenuation.

discharge temperature
protection

compressor acoustic
hoods

Содержание Performer SM Series









































Результаты поиска

Содержание Performer SM Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss Performer SM Series, Выбор и руководство по применению

Результаты поиска

Содержание Performer SM Series

Отзывы:

Бренды по названию

Популярные бренды