background image

User Guide | Gas detecting sensor, type PAGM for CO2 and Halocarbon

© Danfoss | DCS (vt) | 2021.03

8 | BC372016561395en-000101

Second diagnostic screen

Screen item

Description

PPM Level

Parts Per Million level is the current detected gas level, and is the volume concentration 
referenced to standard temperature and pressure.

Average Absorption 
Unit

This is the optical absorbency. In the abscene of the gas the absorbency is 0.00000 au. 
When sampling gas, its value varies proportionally with the gas concentration

µMoles/Liter

This is the absolute concentration in micro-moles per liter of gas.

Detector Voltage

This is a running average of the IR detector’s sensor voltage.

Purge Valve Asterisk (*) The purge valve can be opened and closed by pressing the 

Keypad Left

 

button

. An 

asterisk appears on the display when the purge valve is open causing the monitor to 
draw air from its purge-air port.

Carbon filter maintenance intervals

Approximate ambient refrigerant

Level

Filter replacement interval

0 ppm

6 months

5 ppm

250 hrs

10 ppm

200 hrs

20 ppm

150 hrs

100 ppm

100 hrs

The Refrigerant Monitor requires periodic maintenance to ensure peak performance and accuracy 

including replacement of internal and external filters and calibration accuracy check refer to the 

manual for reference. 

External Coalescing Inline Filter and Internal Hydrophobic Filters replacement filter replacement 

should be carried out at least once every 6 months but is dependent on the environment and usage. 

If used in harsh environment where a large amount of dust and moisture particles are present in 

atmospheres the maintenance intervals need to be shortened.

The intervals for the Purge/Fresh Air Carbon filter might very and is related to time the equipment is 

used and ppm it was exposed to see table below.

When servicing the parts inside the Refrigerant Monitor, disassemble the monitor’s metal chassis as 

follows:

Items Required:

Medium Phillips head screwdriver

Disassemble procedure:

1.  Remove monitor and its battery pack from the soft carrying case.

2.  Unplug battery pack from monitor.

3.  Remove a total of 10 screws from the locations shown in the illustrations below.

4.  Carefully separate the metal chassis.

5.  Locate filters shown in the illustrations below – red circle

6.  Pull off tubing from both ends of filter and remove filter from instrument.

7.  Attach tubing to new filter.  Ensure correct orientation of the filter – the flow direction is 

highlighted with an arrow or/and green label. 

8.  Reassemble monitor.

Replace the following components using Danfoss Maintenance Kit – 

LP-DHGM-MM

a.  Coalescing inline Filter Element (Qty. 1)

b.  Purge/Fresh Air Carbon Filter (Qty. 1)

c.  Hydrophobic Filters (Qty. 2)

Note:

 Individual components not sold separately

After periodic maintenance the unit can experience faults <0200>, <2000>, <8000> please contact 

Danfoss technical support department for further assistance how to adjust the unit settings. 

5.  Maintenance  

5.1   Replacing filters

5.2 

Replacing Internal 

Hydrophobic Filters 

a.

b.

c.

Содержание PAGM











Отзывы: