Danfoss H1P Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 64

Danfoss H1P Series Скачать руководство пользователя страница 56

Charge Pump Repair (removable auxiliary pad)

P106 036E

K100

K150

K500

G450

S150

S300

S250

S100

S300

S200

K200

K100

K400
10 mm
92 Nm [68 ft•lb]

K400
10 mm
92 Nm [68 ft•lb]

1. Using a 10 mm internal hex wrench, remove cap screws (K400).
2. Remove charge pump cover or auxiliary pad (K100) and gasket (K150), and discard the gasket.

Alignment pins (G450) may remain in cover or endcap.

3. Remove auxilliary pump and O-ring (K250), and discard O-ring.
4. Remove charge pump cover screws (K450) and charge pump cover (K550).
5. Remove thrust washer (K500).

Note the orientation of thrust washer. Coated side is towards charge pump coupling (K200).

6. Remove pressure-balance plate (S200) with seal (S300). Discard seal (S300).

Note orientation of valve plate and seal.

7. Remove charge pump coupling K200).
8. Remove charge pump gear set (S100) and outer ring (S150).
9. Inspect carefully the valve and pressure balance plates for wear, scratches or pits.

Scratches on these components will cause a loss of charge pressure.

If any component shows signs of wear, scratching, or pitting, replace it.

Charge Pump Repair (Integrated Auxiliary Pad)

If an auxiliary pump is attached, remove auxiliary pump and coupling before servicing charge pump.

Position pump with front shaft pointing downward. Attach securely to a proper work stand.

Service Manual

H1P 069—H1P 250 Axial Piston Single Pumps

Minor Repair

56 |

©

Danfoss | September 2020

AX152886482551en-000504

«
...
54
55
56
57
58
...
»

Содержание H1P Series

































































Отзывы:

Нет отзывов