manualshive.com logo in svg

Danfoss H1P 069, Руководство по обслуживанию, Страница: 61 / 67

Поделиться
Скачать
Danfoss H1P 069 Скачать руководство пользователя страница 61

6. Install the thrust washer (K500), coated side goes towards charge pump coupling (K200).
7. Install a new cover gasket (K150). If removed, install guide pins (K450).
8. Install the auxiliary pad or charge pump cover and cap screws.
9. Using a 10 mm internal hex wrench, torque the cap screws (K400) to 92 N•m [68 ft•lb],

10. OR using a 6 mm internal hex wrench, torque the cap screws (K450) to 10 N•m [7 lbf•ft].

Torque in sequence below.

Cover (K100) Torque Sequence

P106 196E 

1

2

3

4

5

6

7

8

Cover (K550) Torque Sequence

1

2

3

5

4

6

P106 659E

11. Ensure proper torque on aux. pad screws (K400), and if necessary, replace screws.

If charge pump replacement is necessary, replace complete charge pump kit.

High Pressure Relief Valve Repair

L150

P106 039E

L068

L060

see table

1. Using a hex wrench wrench shown in the table below, remove the HPRVs (L150).
2. Inspect the sealing surfaces in the pump for nicks or scratches, check the valves for damage.
3. Replace any damaged components.
4. Remove and discard the O-rings (L060) and backup rings (L068).

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Minor Repair

 

©

 Danfoss | January 2021

AX152886482551en-000601 | 61

Содержание H1P 069




































































Отзывы:

Нет отзывов