manualshive.com logo in svg

Danfoss EM-PMI540-T1500, Руководство пользователя

Поделиться
Скачать
Danfoss EM-PMI540-T1500 Скачать руководство пользователя страница 24

Main dimensions of the electric machine

Symbol Explanation

L

F

Length of the electric machine frame (including the connection box(es).

L

S

Length of the shaft (from the end of the shaft to the electric machine D-end mounting shoulder).

D

M

Diameter of the flange mounting bore circle.

D

S

Diameter of the mounting shoulder.

For all dimensions of the electric machine, see the product drawings.

Shaft alignment and load

Improper alignment (misalignment) may result in bearing overloads, premature bearing

failures, vibrations and shaft failures. Flexible coupling does not compensate for excessive

misalignment.

The type of the electric machine shaft is cylindrical shaft with diameter of 70 mm h7 and contact length
of 130 mm. The flange type is SAE 1/2 Transmission housing.

Alignment between the shaft and mating structure must be accurate.

The misalignment can be parallel or angular misalignment, or combination of those. With parallel
misalignment, the center lines of both shafts are parallel but they are offset. With angular misalignment,
the shafts are at an angle to each other. Figures below illustrate the parallel and angular misalignment. 

User Guide

EM-PMI540-T1500

Design principles

 

24 | 

©

 Danfoss | July 2021

BC265856800806en-000201

Содержание EM-PMI540-T1500













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды