manualshive.com logo in svg

Danfoss EM-PMI540-T1500, Руководство пользователя

Поделиться
Скачать
Danfoss EM-PMI540-T1500 Скачать руководство пользователя страница 17

Connections and interfaces

1 Grease fill connection (nipple); D-end (+BHS option).

2 Bearing temperature measurement connector, D-end (+BTMP1 option). Type: 4-pin M12 A coded male.

3 Vibration sensor connection points.

Both in the D- and N- end, one on the top and two on the sides.

4 Lifting points.

The two outmost needed for normal lifting.

5 Inner lifting point.

Can be used for additional lifting lug/eye connection and as machine enclosure (power) grounding connection

point when mounted.

6 Grease fill connection (nipple); N-end (+BHS option).

7 Cooling system connections (bores).

8 Mounting foot rails.

Four rails in 90º circular pattern around the frame.

9 Air ventilation plug.

10 Connection boxes (two boxes with -DUAL option).

11 Power connection; cable gland (six glands with -DUAL option).

12 Bearing temperature measurement connector, N-end (+BTMP1 option).

Connected through the connection box. Type: 4-pin M12 A coded male.

13 Cable gland for anti condensation heater connection cables.

Anti connection heater connector inside the connection box.

14 Low voltage connector (measurement connector), low voltage grounding through the connector metal body.

15 Grease escape connections, N-end (+BHS option dependent).

One axial and one radial plug (downwards) in the N-end.

16 Leakage measurement connectors.

One leakage measurement connector in both ends.

17 Grease escape connections, D-end (+BHS option dependent).

One axial plug and four radial plugs in 90º angles around the flange in the D-end.

18 D-end flange mounting (12 connection bores around the flange).

User Guide

EM-PMI540-T1500

Product overview

 

©

 Danfoss | July 2021

BC265856800806en-000201 | 17

Содержание EM-PMI540-T1500













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды