Danfoss ADAP-KOOL AK-PC 781 Скачать руководство пользователя страница 3

Страница: 3 / 14

AK-PC 781 Version 4.1x

Menu operation RC8CE202 © Danfoss 03/2013

Go through the individual functions one by one and make the required settings. When settings have

been made for one controller, the set values may be used as basis in the other controllers of the same

type and with the same software version. Copy the settings by using the copy settings function in the

AKM programme, and adjust subsequently any settings where there are deviations.

NB! If a list is required for noting down the individual settings, a printout can be made of it with a func-

tion in the AKM programme. Read the next section, “Documentation”.

Documentation

Documentation of the settings of the individual controllers can be made with the print function in the

AKM programme. Select the controller for which documentation of the settings is required and select

the “Print Settings” function (cf. also the AKM Manual).

Functions

Shown below are function groups with corresponding measurements and settings. A printout of the

given settings can be made using the AKM function “Print Settings” (see above).

Note

It has been necessary to make selections among the many measurements and settings coming from

the controller.

The operation from the AKM programme cannot contain them all.

If there is a need for access to all measurements and settings, you should make use of Service Tool

type AK-ST 500.

Содержание ADAP-KOOL AK-PC 781














