background image

Operation 

 MCD 

Remote 

Operator 

 

MG.17.E5.02 - VLT

®

 is a registered Danfoss trademark 

Display:

 Indicates the value of the selected data. 

Status LEDs:

 Indicate the status of the starter, and of the RS485 link between the Remote Operator 

and the starter. 

 

The Start LED (Green) indicates that the soft starter is starting, running or stopping. 

 

The Run LED (Green) indicates that the soft starter is providing full voltage to the motor. 

 

The Trip LED (Red) indicates that the soft starter has tripped. 

 

The RS485 Status LED shows the condition of the serial link between the Remote Operator and the soft 
starter.  When this is illuminated the connection is healthy. When the LED is flashing there has been loss of 
communication. 

 

N.B.!: 
Motor current and motor temperature information is only available from MCD 202, 
MCD 500 and MCD 3000 starters. If connected to an MCD 201 open loop soft starter, the 
display will show 2222 instead of motor current and 1.11 instead of motor temperature.  

 

 

N.B.!: 
When using the Remote Operator with MCD 500 models MCD5-0023B ~ MCD5-0068B, the 
motor current and analog output must be normalised using Pars. 6 and 9.  => 
Programmable Parameters for details. 

4.3.

 

Trip Codes  

If the soft starter trips, the CODE and TRIP LEDs illuminate and the relevant trip code is reported on the 
Remote Operator display. Some trip codes are not available from all starter models. 

Code 

Description 

MCD 201

MCD 202  MCD 500  MCD 3000

1-0 

Shorted 

SCR 

     

1-1 

Excess start time 

 

 

 

 

1-2 

Motor overload (Thermal model) 

 

 

 

 

1-3 Motor 

thermistor 

 

 

 

 

1-4 Current 

imbalance 

 

 

 

 

1-5 

Frequency (Mains supply) 

 

 

 

 

1-6 Phase 

sequence 

 

 

 

 

1-7 Instantaneous 

overcurrent 

 

 

 

 

1-8 

Power loss (Power circuit) 

 

 

 

 

1-9 Undercurrent 

 

 

 

 

1-A Other 

trip  

 

 

 

 

1-b 

Time-overcurrent (Bypass overload) 

 

 

 

 

1-C 

Starter communication (between module and 
soft starter) 

 

 

 

 

1-E 

EEPROM read/write failure 

 

 

 

 

1-F Heatsink 

overtemperature 

 

 

 

 

1-H 

Network communication (between module and 
network) 

 

 

 

 

1-J 

Input A trip (Auxiliary input A) 

 

 

 

 

1-L 

FLC too high (FLC out of range) 

 

 

 

 

1-P Motor 

connection 

 

 

 

 

1-U 

CPU 

error 

     

1-Y 

Incorrect main control module 

 

 

 

 

 => the soft starter's LCP for trip details. 

Содержание 175G3061












Отзывы: