background image

E0 Accessories

Fig. 9: E0 with B2123 Fixing plate

Recessed into the rear is a self-locking ball joint with integrated
mounting arm that incorporates an M10 female thread. The E0 rigging
accessories allow different mounting of the E0 loudspeaker as follows: 

- The B2123 Fixing plate allows mounting to walls and ceilings or other

surfaces.

- Single cabinets can be hung from a truss or bar using the E6532

Super Clamp together with the E6533 M10 adapter for the Super
Clamp. The jaw of the Super Clamp can be adjusted to fit bars, or
any other supporting structures with diameters from 13 to 55 mm
(0.5" to 2.2").

- Alternatively the Z5029 TV spigot together with the Z5012 Pipe clamp

can be used for tube diameters from 32 to 50 mm (1.25" to 1.97").

- The Z5035 M10 to 3/8" adapter enables the E0 to be mounted to a

microphone stand, whilst the Z5034 Stand adapter allows the E0 to
be mounted to a loudspeaker stand. The E0 is mounted horizontally
when using either a microphone or loudspeaker stand.

Safety instructions

[S]

WARNUNG!

Under no circumstances should the safety hook [S] be
used to support other loads.

When attaching the accessories as listed above to the
mounting arm of the E0 loudspeaker the spring washer
must always to be used.

When using the accessories as listed above, please refer
to the accessory specific mounting instructions.

Secondary safeties should always be provided and used
when flying or fixing loudspeaker loads overhead. In
case of the E0 loudspeaker there is a safety hook [S] at
the back of the loudspeaker to which a safety rope
should be attached.

Part list E0 accessories

[1]

[2]

[3]

Fig. 10: E0 accessories

The following accessories are included as standard with the E0
loudspeaker:

E0 Loudspeaker black/white (Z0400.000/001):

- 1 x Ball joint with integrated mounting arm M10 

[1]

- 1 x Spring washer M10 

[2]

- 1 x Fixing plate M10 

black/white (B2123.200/201) 

[3]

E0 Manual 

(3.0E)

Page 8 of 10

Содержание E0











Отзывы: