background image

References in the manual

WARNING!

This refers to a potentially dangerous situation which
may lead to personal injury.

CAUTION!

This refers to a potentially dangerous situation which
may lead to personal injury.

IMPORTANT!

This refers to a situation which may cause the equipment
to malfunction.

Note:

Additional informations and/or references

Symbols on the equipment

Please refer to the information in the operating manual.

WARNING! 
Dangerous voltage!

General Information

E0 Manual (incl. Accessories)

   

Version 3.0E, 09/2004, D2099.E.03

©

 by d&b audiotechnik AG 2004; all rights reserved.

The information contained in this manual has been carefully checked for
accuracy, at the time of going to press, however no guarantee is given
with respect to the correctness.

d&b audiotechnik AG accepts no responsibility for any errors or
inaccuracies that may appear in this manual or the products and
software described in it.

Technical specifications, dimensions, weights and properties do not
represent guaranteed qualities.

As manufacterers we reserve the right to make alterations and
modifications within the framework of legal provisions, as well as
changes aimed at improving quality.

Those products which are named in the manual, which at the same time
have registered trade-marks may not always be marked as such. The
lack of the

®

mark does not consequently mean that the product is

freeware. Just as little can be placed on the basis of pending patents or
protection of designs.

d&b audiotechnik AG
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
Tel49-7191-9669-0, Fax +49-7191-95 00 00
E-mail: [email protected], Internet: www.dbaudio.com

Содержание E0











Отзывы: