background image

 
 
 

Classic Stereo amplifier limited warranty 

D’Agostino LLC warrants the Classic Stereo amplifier against manufacturing defects and 
defects in materials for five years from the date of purchase from an authorized Dan 
D’Agostino Master Audio Systems dealer, subject to the conditions listed below: 
 
1) The warranty covers only new products purchased from an authorized D’Agostino LLC 
dealer. 
2) The warranty is non-transferable and is valid only for the original purchaser. 
3) The warranty is valid only if the product has been used according to the instructions in 
the owner's manual. Damage due to accidents or owner abuse or neglect is not covered 
under this warranty. 
4) All service must be performed by an authorized Dan D’Agostino Master Audio Systems 
dealer. Damage resulting from service by other parties is not covered under this warranty. 
5) All products returned for service must be packaged in the original container and must 
include a photocopy of the original purchase receipt. If the original container has been lost 
or discarded, contact D’Agostino LLC for a replacement. 
6) If the product must be shipped back to D’Agostino LLC for warranty service, the 
customer shall pay shipping costs. D’Agostino LLC will pay for return shipping. 
7) Before shipping the product to D’Agostino LLC for service, the customer must first obtain 
a Return Authorization (RA) number by calling D’Agostino LLC. The RA number must be 
marked clearly on the side of the package. 
8) This warranty covers only defects in products made by D’Agostino LLC. It does not cover 
incidental or consequential damages, or damages to other products resulting from defects 
in D’Agostino LLC products.  
9) U.S. residents: Depending on which state you live in, you may have other rights not 
elaborated in this document. For further information, contact D’Agostino LLC. 
10) Residents of other countries: Your authorized importer or dealer bears the direct 
responsibility for warranty coverage of your amplifier. Please contact your importer or 
dealer with requests for service under warranty. D’Agostino LLC will work with your 
importer or dealer to assure that the terms of the warranty are fulfilled. 
 
For questions on warranty and service matters, contact D’Agostino LLC at: 
+1.480.575-3069 or +1.203-644-8743, or e-mail [email protected]
 
 

Содержание classic stereo














Отзывы: