manualshive.com logo in svg

D'Amore engine'ring SMD IM-SG, Руководство пользователя

Поделиться
Скачать
D'Amore engine'ring SMD IM-SG Скачать руководство пользователя страница 11

11 

 

Using  the  IM-SG  to  tune  the  response  of  an 
audio system

 

By using the IM-SG with an audio spectrum analyzer (RTA) 
or with a inexpensive handheld SPL meter, it is possible to 
analyze the frequency response of an entire audio system 
and correct the response with equalization or by swapping 
phase of individual speakers, or by adjusting crossover 
points. 

 

RTA Method  

1.  Connect IM-SG to any auxiliary input of a source unit or 

amplifier  to  use  the  IM-SG  as  a  pink  noise  generator.  
Turn  the  volume  of  the  source  unit  or  amplifier  gain 
down.  

2.  Turn  on  the  IM-SG  by  holding  the 

On

  button  for  1 

second. 

3.  Power on the audio system 
4.  Press  the 

Range 

button  twice  to  activate  Pink  Noise 

mode. 

5.  Increase volume of source unit to a moderate level  
6.  Place the RTA's microphone in the listening position 
7.  View the system's frequency response on the RTA 
8.  Look  for  holes  or  peaks  in  the  frequency  response  of 

the system.  Many times just swapping the phase of the 
rear channels or subwoofer channel  will clear up some 
of these.   

9.  Adjust  tone  controls  and  equalization  to  flatten  any 

peaks or dips in the system's frequency response. 

 

 

Содержание SMD IM-SG

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды