manualshive.com logo in svg

daltile 1020 TS, Руководство по эксплуатации, Страница: 15 / 16

Поделиться
Скачать
daltile 1020 TS Скачать руководство пользователя страница 15

MAINTENANCE

General Maintenance

●

The cooling water should be replaced 
and/or replenished regularly.

●

It is recommended to clean the water con-
tainer, pump, hoses and spray nozzle on a 
regular basis. For example, place the 
pump in a bucket of clean water after the 
sawing job and run the machine for a 
minute or so. This also guarantees
a longer lifetime of the pump.

●

When the machine is not used for a longer
period, the pump should not remain in the
muddy cooling water. Cleaning the pump 
as described above and leaving it outside 
the water container is recommended.

●

Regularly check the saw flanges for wea
ring out and replace if necessary.

V-Belt Inspection, Adjustment

and Replacement:

The DalTile 1020TS is designed with a power
transmission V-belt. In order to ensure the
DalTile 1020TS operates at peak efficiency, the
V-belt should be inspected monthly, and chan-
ged if the V-belt shows damage and/or excessi-
ve wear.

When a new belt is installed, it should be
inspected and re-tensioned after the first forty-
eight (48) hours of operation.

A.  Ensure the ON/OFF Switch is in the OFF 

position.

B.  Unplug from the power source.
C.  Remove the saw blade.
D.  Remove the belt guard.
E.  Inspect the V-belt for cracks, fraying, 

separation and wear. Go to step G if 
replacement is required.

F.  Check the belt for proper tension. If the 

tension T is correct (approx. 1 5/8”) go to 
step Q.

G.  Loosen the motor mounting bolts, if re-

tensioning only go to step M.

H.  Loosen the motor adjustment strap.
I.  Push the motor toward the front of the 

Cutting Head to loosen the V-belt.

J.  Remove the old V-belt.
K.  Install the new V-belt.
L.  Verify the V-belt is seated in the grooves 

of both pulleys.

M.  Tighten the motor adjustment strap to 

remove slack.

N.  Check V-belt tension (proper tension 

1 5/8”)

O.  Repeat steps M and N until proper V-belt 

tension is achieved.

P.  Tighten the motor mounting bolts.
Q.  Install the belt Guard.

DALTILE 1020TS OPERATING MANUAL   V02/2004R1   

PAGE 15

1020  22-07-2005  09:04  Pagina 15

Содержание 1020 TS

















Отзывы:

Нет отзывов