Dalsa Linea HS HL-FM-08K30H-00-R Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 74

background image

Appendix A: GenICam Commands



53

Rotary Encoder Divisor

rotaryEncoderDivider

Specifies a division factor for the rotary encoder
output pulse generator.

1.00
DFNC
Beginner

Rotary Encoder Rescaler
Order

Multiplier Divider

Divider Multiplier

rotaryEncoderRescalerOrder

multiplierDivider

dividerMultiplier

Specifies the order that the multiplier and divider are
applied.

The signal is multiplied before been divided.

The signal is divided before been multiplied

1.00
DFNC
Beginner

Trigger Delay

TriggerDelay

Allows the trigger to the sensor to be delayed
relative to camera input trigger

1.00
DFNC
Beginner

Line Selector

Line 1
Line 2
Line 3
Line 4
Line 5
Line 6

LineSelector

GPIO 1
GPIO 2
GPIO 3
GPIO 4
GPIO 5
GPIO 6

Selects the physical line (or pin) of the external
device connector to configure.

Index of the physical line and associated I/O control
block to use.

1.00
DFNC
Beginner

Output Line Source

Off

On

outputLineSource

off

on

Selects which features control the output on the
selected line.

Line output level is controlled by the
outputLineSoftwareCmd feature

Line output level is controlled by
outputLinePulseDelay, outputLinePulseDuration,
and LineInverter features

1.00
DFNC
Beginner

Output Line Pulse Delay

outputLinePulseDelay

Sets the delay (in µs) before the output line pulse
signal. Enabled by the OutputLineSource feature.

1.00
DFNC
Beginner

outputLinePulseDuration

outputLinePulseDuration

Sets the width (duration) of the output line pulse in
microseconds.

1.00
DFNC
Beginner

Line Inverter

On

Off

LineInverter

On

Off

Controls whether to invert the polarity of the selected
input or output line signal.

1.00
DFNC
Beginner

Output Line Software
Command

outputLineSoftwareCmd

Set the GPIO out value when outputLineSource is
off.

1.00
DFNC
Expert

Refresh Line Status

refreshLineStatus

Update the LineStatus feature

1.00
DFNC
Expert

Line Status

LineStatus

Returns the current state of the GPIO line selected
with the LineSelector feature (RO)

1.00
DFNC
Expert

«
...
51
52
53
54
55
...
»

Содержание Linea HS HL-FM-08K30H-00-R











































































Отзывы:

Нет отзывов

Похожие инструкции для Linea HS HL-FM-08K30H-00-R

Бренд: VEKOOTO Страницы: 18

Бренд: Zenith Страницы: 18

Бренд: Digital Concepts Страницы: 2

Бренд: CIS Страницы: 29

Бренд: Xoro Страницы: 33

smc Pentax-D FA Macro 100mm f/2.8

Бренд: Pentax Страницы: 12

Бренд: Laon People Страницы: 46

Бренд: Q-See Страницы: 2

CAMEDIA C-480 ZOOM

Бренд: Olympus Страницы: 100

Бренд: Z3 Technology Страницы: 6

Бренд: Astrel Instruments Страницы: 21

Бренд: Exakta Страницы: 1

Бренд: IDEAL Страницы: 23

Бренд: Zavio Страницы: 14

Lumix DMC-FZ50PP

Бренд: Panasonic Страницы: 69

Lumix DMC-FZ7PP

Бренд: Panasonic Страницы: 54

Бренд: Genee Страницы: 27

QuickClix QC-2185

Бренд: Argus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды