background image

 

Dale Power Solutions Ltd

 

Salter Road, Eastfield Industrial Estate, Scarborough, North Yorkshire, YO11 3DU, UK 

info@dalepowersolutions.com  |  www.dalepowersolutions.com  |

  

+44 (0) 1723 583511

 

Installation 

Siting considerations 

Before unpacking and installing the unit, consider the following: 

■  DO NOT expose the UPS to high temperatures, water ingress, flammable or corrosive gas, dust, 

direct sunlight or explosives.  

■  Locate the UPS indoors on a level surface as close as possible to the equipment it will be powering to 

minimise cable voltage drops. If required, allow enough spare cable to move the UPS after 
installation. 

■  Maintain a gap of at least 50 cm from walls or other equipment, and ensure the ventilation holes/slots 

at the front and rear of the units are not obstructed. 

■  For improved product reliability ensure cool air is available at the front of the unit. 
■  Battery location. We recommend you site batteries in a separate room to maintain the optimum 

working temperature of between 15°C and 25°C. As an approximation, battery life is halved for every 
10K (10°C) rise in temperature. 

Wiring considerations 

To ensure a safe installation please follow these instructions and the local electrical code of the area or 
country in which you are installing the equipment: 

■  If the UPS is to be supplied from a local transformer, ensure the transformer kVA rating is at least 

50% greater than the UPS output kVA rating and the output is 4-wire star configuration. 

■  Use circuit breakers and cables with the correct rating (see the next section). 
■  Always fit an MCB between the mains supply live lines only and the UPS input (see Figure 2). 

 

Caution:

 Do not fit an MCB in the neutral line. 

■  Because of the high leakage current (see 

Error! Reference source not found.

 below), permanently 

hard wire all the a.c. cables. 

■  Fit ring terminal crimps on the ends of all cables that fasten to studs (see 

Error! Reference source 

not found.

 on page 

Error! Bookmark not defined.

). 

■  Fit a 3 pole MCCB, with a suitable d.c. voltage rating and breaking capacity, between the battery and 

the UPS (see Figure 2). 

 

Caution:

 The UPS is designed to work with a centre-tap battery only. 

■  Although it may not be absolutely necessary, we recommend you fit an MCB between the UPS and 

the load to protect the output load and cables in the event of a fault (see Figure 2). You may also wish 
to connect the UPS output to your load via a power distribution unit (PDU). 

■  Ensure correct phase rotation in the 3-phase wiring. 

 

 

 

 

 

 

 

Содержание E420














































Отзывы: