manualshive.com logo in svg

DALBO MAXIDISC 300, Руководство оператора

Поделиться
Скачать
DALBO MAXIDISC 300 Скачать руководство пользователя страница 22

 

 

MAXIDISC 

 

 

Side 22 

 
Replacing angle adjustment seals  
 
Fig. 10 

 

Cylinder 50/30-150 

 
1

 

Empty the oil from the cylinder by carefully moving the cylinder back and forth. 

2

 

Move  the  piston  to  the  middle  position.  Unscrew  the  gland  (pos.  3)  from  the 
cylinder casing (pos. 1). (A special tool is needed to remove the gland). If the 
gland is stuck, it may help to warm up the very front of the socket. When the 
gland has been unscrewed, pull the piston towards the gland. Pull the piston 
rod completely out of the cylinder casing (pos. 1). 

3

 

Remove the self-locking nut (pos. 10) holding the sleeve (pos. 4). 

4

 

Pull the sleeve (pos. 4) off the piston rod (pos. 2). 

5

 

Pull the gland (pos. 3) off the piston rod (pos. 2). 

6

 

Remove the seals from the gland and the sleeve (pos. 5+6+7+8+9). 

7

 

Clean  all  parts  thoroughly.  Check  for  filings,  shavings,  burrs,  and  make  sure 
that  there  is  no  rust  around  the  scraper  ring  (pos.  5)  in  the  gland.  If  rust  is 
found, it must be removed. 

 
Assembly 
1

 

Assemble the new seals (pos. 5+6+7+8+9) into the gland and the sleeve. 

2

 

Lubricate the screw threads on the gland (pos. 3) and the cylinder casing (pos. 
1) with oil. 

3

 

Mount the gland (pos. 3) onto the piston rod.  

4

 

Mount the sleeve (pos. 4) and screw on the self-locking nut with Loctite. Make 
sure that the screw threads are completely clean and free from oil or other im-
purities before using Loctite. Do not refill the oil for the first 12 hours after the 
application of Loctite. 

5

 

Lubricate the outermost seal of the sleeve that has contact with the cylinder 
casing and the inside of the cylinder casing, then guide the piston rod into the 
middle position of the casing. 

6

 

Screw the gland onto the casing and tighten. 

Содержание MAXIDISC 300




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды