1. Before inserting the plug into an electrical outlet, make sure that the
electrical supply in your area matches that on the rating label on the
unit.
2. Carefully remove the heater from the plastic bag and the carton.
3. Place the heater on a firm level surface ,setting the master button to
“-”position.plug the cord set into a AC220-240V electrical outlet,with
“BEE” sounds the “Power”light is on .
1) HEATING PERPARE
Set time
turn on the heater,set the time as right time.Press remote control “
”
button,light on control panel,LED display shows 00:00 and “Mo”light on.
HOUR
Press “Set” button one time,LED display front “00” twinkle,
press“
two buttons set the Hours from 01--00(01=1 o’clock,02=2
o’clock...00=24 o’clock ect.)
MINUTE
Press “Set” button again,LED display behind “00” twinkle, press
“
two buttons set the minutes from 00--59(01=1 Minute,02=2
Minute ect.)
WEEK
Press “Set” button again,“Mo”light twinkle ,press “
two
buttons set the week from Mo--Su (Mo=Monday...Su=Sunday ect.)
PS
:Press “Set” button,screen shows number will twinkle 5 seconds,you
should operate in time ,otherwise appliance will get back to standby.
(Appliance will keep the right time until power off)
2)General Using OPERATION
1. Turn the heater ON by pressing remote control the ON/OFF
button ,the unit will blow the cold air .
2. Pressing the “MODE” button on remote control ,the unit will blow the
warm air and
will light on.
3. Pressing the “MODE” button second times on remote control,the unit
will blow the hot air and the
will light on
4. Pressing the “MODE” button Three times on remote control,the unit will
blow the cold air
PS:For smart operate,customer only press the one start button near
about master button,the heater will working with hot air and
Will light on
3) 24H Timer FUNCTION
1. Open the appliance as working conditions,(fan,warm,hot are all
ok).This function through by Remote control “
”
button .
2. Press “
” button ,set the timer up to 24 hours,keep press “
”
button to increase the hours from 00--24(00=close,01=1hour,02=2
hours...24=24 hours ect.) and the “
” light is on.
PS:set as “00” means no set timer ,the “
” light is off.
4)THERMOSTAT INSTRUCTIONS
1. Open the appliance as working conditions,(fan,warm,hot are all
ok).This function only through by Remote control.
2. To adjust temperature,press the “
” to set the desired
temperature and the temperature set from 10
℃
to 49
℃
3. When the air temperature drops 2 degree below the set temperature,the
heater will start heating with ”I/W”(1000W).
4. When the air temperature drops 4 degree below the set temperature
,the heater will start heating with”II/H”(2000W).
5. When the air temperature high 1 degree or
≤
the set temperature,the
heater will blow the cold air .
5) Week Timer FUNCTION
1. Open the appliance as working conditions,(fan,warm,hot are all
ok).This function only through by Remote control.
2.
WEEK
Press “ ”button 1
st
time,”
” lights on,means “Monday”.
HOUR
Press “
” button 2
nd
times, LED display front “00” twinkle,
press“
”
two buttons set the Hours from 01--00(01=1 o’clock,02=2
o’clock...00=24 o’clock ect.)
MINUTE
Press “
” button 3
rd
times,LED display behind “00” twinkle
“
”
two buttons set the Hours from 00--59(01=1 Minute,02=2
