DAL-BO MINIMAX Скачать руководство пользователя страница 2

DALBO COMPACT 930 cm

 

 

Congratulations with your new COMPACT. For safety reasons and to obtain optimaluse ofthe machine you 

should read through the following instructions before putting the

 

machine into operation.

 

 

© Copyright 1995. All rights reserved DALBO A/S

 

Points, which are essential as regards to safety, are marked byV.

 

 

Re-tighten all bolted connections after a few hours use.

 

Do not operate the hydraulics without the machine being securely attached to a tractor.

 

 

Operation must only be carried out from a sitting position in the tractor, and no persons must 

be on or in the close proximity of the machine.

 

Must not be operated by children.

 

The driver is responsible for correct use of lights and markings according to the Road Traffic 
Aet/ the Highway Code.

 

 

It is the driver' s responsibility to ensure that the capacity of the tractor used is sufficient to 
handle the roller properly. It must be at least 100 HP

 

 

Your Compact has:

 

Serial number: _ _ _ _ _ _ _ _ _  

.Type description: _ _ _ _ _ _  

_

 

Manufacturing month: 

.Net weight kg: 

  

 

 

Please always quote the serial number in connection with any enquiries regarding spare parts.

 

An index of spare parts, which facilitates the overview of single parts, can be found at the very back.

 

 

EU-COMPLAINCE DECLARATION

 

DALBO A/S

 

DK-7183 Randbøl

 

declares herewith that the above machine is manufactured in accordance with the provisions of directive 2006/42/EC, which 
replaced directive 98/373/EC and change directives 91/368/ECC, 93/44/ECC and 93/68/ECC on harmonisation of member state 
legislation concerning health and safety requirements related to the construction and manufacture of machines.

 

 
 
 
 

 

hine corresponds to the safety requirements in the European Safety Guidelines.

 

 

 

Date:      

 

 

 

Carsten Jensen, CEO

 

Содержание MINIMAX














Отзывы: