manualshive.com logo in svg

Daktronics VF-2100, Руководство пользователя

Поделиться
Скачать
Daktronics VF-2100 Скачать руководство пользователя страница 13

Mechanical Installation

9

Traffic Cabinet Mounting

Ground Mounting

Secure the traffic cabinet to a concrete pad using anchor bolts. Daktronics recommends 

using 

3

/

4

" stainless steel anchor bolts. When anchoring the traffic cabinet to the concrete 

pad, make sure the bottom of the cabinet allows for water drainage. Do not seal the 

cabinet to the concrete pad as this prevents water from draining properly. 
The conduit for power and signal enter through the open area in the bottom of the 

cabinet.

Pole Mounting

Mount the cabinet using the pole-mount brackets. Make sure the brackets are secured 

at all locations.

LIE Mounting

LIEs are designed for pole-mounting. After installing the LIE, select power and signal 

entrances on the bottom, sides, or rear of the LIE. Prior to drilling, be aware of internal 

component locations to avoid damaging the components. Ensure the entrances will not 

obstruct the drain holes on the bottom of the LIE.
Seal any hole punched or drilled in the LIE with either a watertight plug or with a 

watertight conduit hub to prevent water from entering the LIE.

Содержание VF-2100




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды