Daktronics VANGUARD VL-3500 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 33

background image

Mechanical Installation

4

Display Lifting

The top of the display is equipped with

1

/

2

" eyebolts for lifting the display. Lift the display

using a lifting bar. Use every eyebolt, and maintain a 90° lifting angle as shown in

to prevent eyebolt failure.
The eyebolts are designed to carry only the weight of the display cabinet. Do not lift the

mounting structure or other additional weight. Do not permanently support the display

with the eyebolts.

Note:

Leave 4" (10 cm) of unobstructed space above the display so the eyebolt can

be removed. No clearance is required once the eyebolt is removed.

Display Mounting

Securely mount each display to a suitable mounting structure provided by others.

Daktronics attached clip angles to the display for mounting. Use all clip angles when

mounting the display.

Use appropriate hardware to support the weight of the display. Have a qualified

engineer inspect the mounting structure.

Note:

Daktronics is not responsible for mounting methods or the structural integrity of

support structures provided by others.

After installing the display, inspect the top and sides of the display for any openings

that may allow moisture to enter the display. Seal openings with silicone or another

waterproof sealant. Not sealing openings may void the warranty.

Figure 2:

Correct Lifting Procedures

«
...
6
7
8
9
10
...
»

Содержание VANGUARD VL-3500 Series


































Отзывы:

Нет отзывов

Похожие инструкции для VANGUARD VL-3500 Series

Бренд: Acer Страницы: 31

Бренд: Acer Страницы: 17

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 25

Бренд: Acer Страницы: 10

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 15

Бренд: Acer Страницы: 15

Бренд: Acer Страницы: 15

Бренд: Acer Страницы: 12

Бренд: Acer Страницы: 3

Бренд: Acer Страницы: 23

Бренд: Acer Страницы: 27

Бренд: IBM Страницы: 32

Бренд: NEC Страницы: 2

MultiSync FP1375X

Бренд: NEC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды