Daktronics VANGUARD VL-3500 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 33

background image

Power Installation

9

Signal Termination from Computer to Display

Ethernet

An Ethernet network system requires a Cat-5 cable. Signal travels from the Local Area

Network (LAN) to the Ethernet jack (J4) on the controller.
The signal cable terminates within the display at the controller. The opposite end

terminates at the control computer.

Fiber-Optic Ethernet

A fiber-optic network requires a 4-fiber, fiber-optic cable. Two fibers are used, leaving the

other two as spares. Either use direct burial or route the cable in conduit. Do not subject

fiber-optic cable to mechanical flexing.
If the media converter is installed in the sign, the signal cable terminates at the fiber

signal converter located either in an external signal enclosure or within the display.

Ethernet Surge Card (J2)

Ethernet In (J4)

Pin 1 (TX+)

Pin 1 (TX+)

Pin 2 (TX-)

Pin 2 (TX-)

Pin 3 (RX+)

Pin 3 (RX+)

Pin 4 (+VDC)

Pin 4 (CHGND)

Pin 5 (+VDC)

Pin 5 (CHGND)

Pin 6 (RX-)

Pin 6 (RX-)

Pin 7 (GND)

Pin 7 (CHGND)

Pin 8 (GND)

Pin 8 (CHGND)

«
...
11
12
13
14
15
...
»

Содержание VANGUARD VL-3500 Series


































Отзывы:

Нет отзывов

Похожие инструкции для VANGUARD VL-3500 Series

Бренд: Samtron Страницы: 115

Бренд: Garmin Страницы: 8

Бренд: E Instruments Страницы: 2

PrecisionSensor Pro BP 2590 Instructions

Бренд: Braun Страницы: 66

BeeConnect Plus 50120

Бренд: Reer Страницы: 64

Бренд: Qardio Страницы: 32

Бренд: Excel Technology Страницы: 7

Бренд: Eye Sight Technology Страницы: 4

Бренд: AG-EXPRESS ELECTRONICS Страницы: 28

Бренд: Rockwell Automation Страницы: 64

VX710 - 17" LCD Monitor

Бренд: ViewSonic Страницы: 78

Бренд: Z Microsystems Страницы: 35

Бренд: Hanns.G Страницы: 1

Бренд: Zenith Страницы: 36

Бренд: AOC Страницы: 1

Бренд: NEC Страницы: 113

Бренд: V7 Страницы: 12

Бренд: Geemarc Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды