Daktronics Tuff Sport BB-2102 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 112

Daktronics Tuff Sport BB-2102 Скачать руководство пользователя страница 39

Scoreboard Options

33

Section 6:

Scoreboard Options

6.1 Horns

Daktronics Tuff Sport scoreboards are equipped with a 120 VAC vibrating horn mounted
behind the scoreboard face. The horn sounds automatically when the period clock counts
down to zero, or when manually triggered by the operator using the control console.

Installation of an optional 12 VDC horn is detailed in

Drawing A-148960

in

Appendix C

.

Louder trumpet horns are also available. Contact Daktronics for information and pricing.

Adjusting Horn Volume

CAUTION:

The scoreboard horn is a 120 VAC device. Turn off the power to the scoreboard

before adjusting the horn.

The volume for the electronic, buzzer-type horn is set at its maximum level at the factory. If
the horn is too loud, reduce its volume by adjusting the setscrew mounted in the front of the
horn. A plastic tip on the screw touches the horn's diaphragm, reducing the volume. Turn the
screw clockwise and test the volume by operating the horn from the scoreboard control
console. Continue adjusting and testing until the desired volume level is obtained.

Note that with the noise of spectators, the horn will not seem as loud as when it is being
tested in an empty area, so be sure to set the volume according to the acoustics of the facility.

6.2 Radio Control

Radio control is an option for Daktronics Tuff Sport scoreboards. The system provides
scoreboard control via a 2.4 GHz, extra-high frequency FM signal.

The radio transmitter and receiver are not standard equipment. This setup requires a control
console equipped with a radio transmitter as well as a radio receiver plugged into the
driver/power enclosure and mounted internally to the front panel of the scoreboard.

For additional information about this option, contact a Daktronics representative; for
complete information on setting up radio communication control, refer to the

Gen V Radio

Installation Manual (ED-13831)

or the

Gen VI Radio Installation Manual (DD2362277)

,

both available online at

www.daktronics.com/manuals

6.3 Visual Horn Indicator (VHI)

In addition to the horn, Daktronics offers both incandescent and LED visual horn indicators
that light up when the buzzer sounds. To install the VHI, users must tap into the existing
horn wiring to provide power and signal. For more information about installing the VHI
options, refer to the

Visual Horn Indicator Installation Instructions (ED-13397)

or the

BB-2133 LED Indicator Installation Instructions (ED-13806)

. Both manuals are available

online at

www.daktronics.com/manuals

«
...
37
38
39
40
41
...
»

Содержание Tuff Sport BB-2102

















































































































Отзывы:

Нет отзывов