Daktronics Sportsound Rack SSR-100 Скачать руководство пользователя

Страница: 5 / 32

Introduction 1

Section 1: Introduction

This manual explains the operation of the Sportsound

Rack (SSR) 100. For additional information regarding

the safety, installation, operation, or service of this system, refer to the telephone numbers listed in Section 6.

This manual is not specific to a particular installation. Project-specific information takes precedence over any

other general information found in this manual.

IMPORTANT SAFEGUARDS

• Read and understand all instructions before beginning the installation process.

• Do not drop the control equipment or allow it to get wet.

• Do not disassemble control equipment or electronic controls of the system; failure to follow this

safeguard will make the warranty null and void.

• Always turn off and/or unplug the control equipment when it is not in use. This keeps equipment

protected from power spikes and lightning.

• Never yank the power cord from the outlet. Grasp the plug and pull to disconnect.

• Do not let any power cord touch hot surfaces or hang over the edge of a table that would damage or

cut the cord. Arrange the cord with care so that it will not be tripped over.

• Inspect control equipment for shipping damage such as rattles and dents, and verify that all

equipment is included as itemized on the packing slip. Immediately report any problems to

Daktronics; save all packing materials if exchange is necessary.

• Keep equipment covered when possible to protect from dust and debris.

1.1 Resources

Figure 1

illustrates a Daktronics drawing label. The drawing

number is located in the lower-right corner of a drawing. This

manual refers to drawings by listing the last set of digits and

the letter preceding them. In the example, the drawing would

be referred to as

Drawing D-1007804

. All references to drawing

numbers, appendices, figures, or other manuals are presented in

bold typeface. Any drawings referenced in a particular section

are listed at the beginning of it as shown below:

Reference Drawing:

System Riser Diagram .................................................................................................

Drawing D-1007804

All drawings referenced in this manual are found in

Appendix A

Daktronics identifies manuals by the DD or ED number located on the cover page. For example, this manual

would be referred to as

DD2746938

Daktronics has a searchable knowledgebase of common questions and troubleshooting tips:

www.daktronics.com/support

Visit the Daktronics Support YouTube channel to learn how to properly operate Sportsound racks:

www.youtube.com/DaktronicsSupport

Drawing Number

Figure 1:

Drawing Label

Содержание Sportsound Rack SSR-100

































Результаты поиска

Содержание Sportsound Rack SSR-100

Отзывы:

Похожие инструкции для Sportsound Rack SSR-100

Бренды по названию

Популярные бренды

Daktronics Sportsound Rack SSR-100, Руководство по эксплуатации

Результаты поиска

Содержание Sportsound Rack SSR-100

Отзывы:

Похожие инструкции для Sportsound Rack SSR-100

Бренды по названию

Популярные бренды