background image

The modem is held in place with the use of plastic rails known as a "snap trac." To replace a failed 
modem, disconnect all attached cables and carefully "snap" it out of the rails. Insert the new 
modem by first laying one end into the rails of the "snap track," then pivot it up and snap into 
place. 

4.3 Power 

Summary 

The power routing for the display can be summarized as follows: 
 

1. 

Incoming power terminates at the termination block (TB41) within the power termination 
enclosure. Before leaving the enclosure, the power is sent through a fuse and an RFI electrical 
filter. 

 

2. 

Power for the controller board passes through a transformer located on the controller/power panel. 

 

3. 

3VDC power supplies are used to power the modules. Power supplies are pre-set at 3.6 VDC. 

4.4  Service and Diagnostics 

The following sub-sections address servicing of the following display components: 
 

· 

transformer, RFI filter and fuse 

· 

controller 

· 

modules, drivers and power supplies 
 

The sub-sections also address any diagnostic LEDs, fuses and signal/power connectors found on the 
unit. 
 
On the components are denoted as follows. 

 

Component… 

Denoted As… 

Location… 

Filter, Transformer 
and Fuse 

0A-1215-4002 

Inside the power termination box (behind module 
A202) 

Controller 

0A-1146-0035 

Inside the controller/power panel (behind module 
A201) 

Modules 0A-1266-2002 

0A-1266-2003 

Over entire face of the display (includes driver) 

Power Supplies 

0A-1289-4001 
0A-1289-4002 
0A-1289-4003 
0A-1289-4004 
0Z-9854-3300P 
0Z-10162-3300P 
0Z-10095-300P 
0Z10052-3300P 

Varies by sign size 

T ansformer, RFI Filter and Fuse  

r

Transformer 

The transformer is located in the upper portion of the power enclosure (T1). To replace the 
transformer, first disconnect all the wires attached to it. 

Turn off power to the display before 

Maintenance and Troubleshooting 

4-2

 

Содержание Galaxy AF-3050 Series
























































































Отзывы: